There’s nothing more frustrating than a Poulan hedge trimmer that won’t move. You’re trying to trim your hedges, but the blades are stuck and you can’t get them to budge. This is a common problem, and it can be caused by a variety of issues. In this guide, I’ll walk you through the steps to troubleshoot a Poulan hedge trimmer that won’t move. I’ll also provide tips on how to prevent this problem from happening in the future. So if you’re ready to get your hedge trimmer back in action, let’s get started!
Why Blades Won’T Move On Poulon Hedge Trimmer
Why Blades Won’T Move On Poulon Hedge Trimmer
Defective or damaged drive belt:
The drive belt is responsible for transferring power from the motor to the blades. If the belt is damaged or missing, the blades will not be able to move.
Stuck or seized blade:
The blades can become stuck or seized if they are not properly lubricated. This can happen if the trimmer is used in wet or dusty conditions, or if the oil level is low.
Clogged or damaged air filter:
A clogged or damaged air filter can restrict airflow to the engine, causing it to overheat and stall. This can prevent the engine from generating enough power to turn the blades.
Dirty or damaged spark plug:
A dirty or damaged spark plug can prevent the engine from firing, which will also prevent the blades from moving.
Low oil level:
A low oil level can cause the engine to overheat and stall. This can also prevent the engine from generating enough power to turn the blades.
Engine problems:
The engine may be damaged or malfunctioning for a variety of reasons, such as a bad carburetor, a faulty ignition coil, or a cracked piston. This can prevent the engine from generating enough power to turn the blades.
How to Troubleshoot: Poulon Hedge Trimmer Blades Won’t Move
Symptoms
The blades on your Poulon hedge trimmer won’t move at all.
The blades move very slowly or intermittently.
The blades make a grinding or squealing noise when they do move.
The blades are not cutting through branches as well as they used to.
Possible Causes
There are a number of possible causes for this problem, including:
A dirty or clogged air filter:
A dirty or clogged air filter can restrict airflow to the engine, causing it to run poorly and the blades to not move as quickly.
A dirty or clogged carburetor:
A dirty or clogged carburetor can also cause the engine to run poorly and the blades to not move as quickly.
A bad spark plug:
A bad spark plug can prevent the engine from firing properly, which will also cause the blades to not move.
A loose or damaged spark plug wire:
A loose or damaged spark plug wire can also prevent the engine from firing properly, which will also cause the blades to not move.
A bad fuel filter:
A bad fuel filter can restrict the flow of fuel to the engine, causing it to run poorly and the blades to not move as quickly.
A low fuel level:
If the fuel level in the tank is too low, the engine will not have enough fuel to run properly and the blades will not move.
A problem with the engine governor:
The engine governor is responsible for regulating the speed of the engine. If the governor is not working properly, the engine may run too fast or too slow, which can cause the blades to not move properly.
A problem with the blade control linkage:
The blade control linkage is responsible for connecting the throttle to the blades. If the linkage is not working properly, the blades may not be able to move when you engage the throttle.
A problem with the blade drive belt:
The blade drive belt connects the engine to the blades. If the belt is damaged or worn out, it may not be able to transfer power from the engine to the blades, causing them to not move.
Troubleshooting Steps
To troubleshoot this problem, you will need to:
1. Check the air filter:
Remove the air filter and inspect it for dirt or debris. If the filter is dirty, clean it or replace it with a new one.
2. Check the carburetor:
Remove the carburetor and inspect it for dirt or debris. If the carburetor is dirty, clean it or replace it with a new one.3. Check the spark plug:
Remove the spark plug and inspect it for damage. If the spark plug is damaged, replace it with a new one.
4. Check the spark plug wire:
Inspect the spark plug wire for damage or corrosion. If the wire is damaged or corroded, replace it with a new one.
5. Check the fuel filter:
Remove the fuel filter and inspect it for dirt or debris. If the filter is dirty, clean it or replace it with a new one.
6. Check the fuel level:
Make sure that the fuel level in the tank is at least half full.
7. Check the engine governor:
Inspect the engine governor for damage or wear. If the governor is damaged, replace it with a new one.
8. Check the blade control linkage:
Inspect the blade control linkage for damage or wear. If the linkage is damaged, replace it with a new one.
9. Check the blade drive belt:
Inspect the blade drive belt for damage or wear. If the belt is damaged or worn out, replace it with a new one.
Conclusion
If you have tried all of the troubleshooting steps and the problem persists, you may need to take your hedge trimmer to a qualified service technician for further diagnosis and repair.
Also Read THis: Can Start My Stihl Hedge Trimmer Won’T
FAQs: Poulon Hedge Trimmer Blades Won’t Move
Why won’t the blades on my Poulon hedge trimmer move?
There are a few possible reasons why the blades on your Poulon hedge trimmer might not be moving. Here are some of the most common causes:
The blades are not properly aligned: If the blades are not aligned correctly, they will not be able to cut through branches. To check if the blades are aligned, turn the trimmer on and look at the blades. The blades should be parallel to each other and should not be touching. If the blades are not aligned, you can try to adjust them by turning the adjustment screws on the side of the trimmer.
The blades are dull: If the blades are dull, they will not be able to cut through branches. To check if the blades are dull, try to cut through a piece of wood. If the blades are dull, they will not be able to cut through the wood easily. You can sharpen the blades by using a file or a sharpening stone.
The trimmer is not getting enough power: If the trimmer is not getting enough power, the blades will not be able to move. To check if the trimmer is getting enough power, try plugging it into a different outlet. If the trimmer is still not getting enough power, you may need to replace the battery.
The trimmer is overheating: If the trimmer is overheating, the blades will not be able to move. To check if the trimmer is overheating, feel the sides of the trimmer. If the trimmer is hot to the touch, it is overheating. You can let the trimmer cool down for a few minutes before trying to use it again.
How do I align the blades on my Poulon hedge trimmer?
To align the blades on your Poulon hedge trimmer, follow these steps:
1. Turn off the trimmer and unplug it from the power outlet.
2. Remove the guard from the trimmer.
3. Locate the adjustment screws on the side of the trimmer.
4. Turn the adjustment screws clockwise to move the blades closer together or counterclockwise to move the blades farther apart.
5. Reattach the guard to the trimmer.
6. Turn on the trimmer and check to see if the blades are aligned correctly.
How do I sharpen the blades on my Poulon hedge trimmer?
To sharpen the blades on your Poulon hedge trimmer, follow these steps:
1. Turn off the trimmer and unplug it from the power outlet.
2. Remove the guard from the trimmer.
3. Locate the blades on the trimmer.
4. Use a file or a sharpening stone to sharpen the blades.
5. Reattach the guard to the trimmer.
6. Turn on the trimmer and test the blades to see if they are sharp.
What should I do if my Poulon hedge trimmer is not getting enough power?
If your Poulon hedge trimmer is not getting enough power, follow these steps:
1. Check the power cord to make sure it is plugged in securely.
2. Try plugging the trimmer into a different outlet.
3. If the trimmer is still not getting enough power, you may need to replace the battery.
What should I do if my Poulon hedge trimmer is overheating?
If your Poulon hedge trimmer is overheating, follow these steps:
1. Turn off the trimmer and unplug it from the power outlet.
2. Let the trimmer cool down for a few minutes.
3. If the trimmer is still overheating, you may need to have it serviced.
