There’s nothing more frustrating than having a pressure washer that’s not working properly. And when it comes to pressure washers, one of the most common problems is a soap injector that’s not working. This can be a major inconvenience, especially if you’re trying to clean a large area or if you need to use a specific type of soap.
In this guide, I’ll walk you through the steps to troubleshoot a blue clean pressure washer soap injector that’s not working. I’ll also provide some tips on how to prevent this problem from happening in the future.
So if you’re having trouble with your pressure washer’s soap injector, read on for help!
Why Blue Clean Pressure Washer Soap Injector Not Working
Blue Clean Pressure Washer Soap Injector Not Working
Blocked nozzle:
The most common reason for a soap injector not working is a blocked nozzle. This can be caused by dirt, debris, or soap scum. To fix this, remove the nozzle and clean it with a small brush or needle.
Dirty or damaged hose:
If the hose between the soap injector and the pressure washer is dirty or damaged, it can prevent the soap from flowing properly. To fix this, clean the hose with a hose cleaner or replace it if it is damaged.
Incorrect pressure setting:
The pressure setting on the pressure washer may be too high for the soap injector to work properly. To fix this, lower the pressure setting.
Faulty soap injector:
If the soap injector is faulty, it will not be able to inject soap into the water stream. To fix this, replace the soap injector.
Blue Clean Pressure Washer Soap Injector Not Working
Symptoms
There are a few symptoms that may indicate that your Blue Clean pressure washer soap injector is not working properly. These include:
The soap tank is not filling up with soap.
The soap is not being dispensed from the nozzle when you trigger the spray gun.
The soap is being dispensed from the nozzle, but it is not aerated properly.
The soap is being dispensed from the nozzle, but it is not coming out in a steady stream.
Troubleshooting
If you are experiencing any of the symptoms listed above, there are a few things you can check to troubleshoot the problem.
1. Check the soap tank:
Make sure that the soap tank is filled with soap and that the lid is properly closed. If the tank is empty or the lid is not closed properly, the soap will not be able to flow through the injector and into the spray gun.
2. Check the soap injector:
The soap injector is a small, cylindrical device that is located near the top of the pressure washer. It is responsible for pumping the soap from the tank into the spray gun. To check the soap injector, remove the lid from the soap tank and look inside. You should see a small, black tube that is connected to the injector. If the tube is clogged, you can try cleaning it with a small brush or pipe cleaner. If the tube is damaged, you will need to replace the injector.3. Check the spray gun:
The spray gun is the device that you use to direct the water and soap from the pressure washer. To check the spray gun, remove the nozzle from the gun and look inside. You should see a small, metal screen that is located at the end of the nozzle. If the screen is clogged, you can try cleaning it with a small brush or pipe cleaner. If the screen is damaged, you will need to replace the nozzle.
Prevention
You can prevent problems with your Blue Clean pressure washer soap injector by following these tips:
Keep the soap tank filled with soap.
Close the lid of the soap tank tightly after each use.
Clean the soap injector regularly.
Clean the spray gun regularly.
By following these tips, you can help to ensure that your Blue Clean pressure washer soap injector is working properly and that you are getting the most out of your pressure washer.
Also Read: Bosch Pressure Washer Not Working
FAQs: Blue Clean Pressure Washer Soap Injector Not Working
Why is my Blue Clean pressure washer soap injector not working?
There are a few possible reasons why your Blue Clean pressure washer soap injector may not be working. Here are some of the most common causes:
The soap injector is clogged: This is the most common cause of a soap injector not working. To fix this, you can try to clean the injector with a small brush or needle. If the injector is still clogged, you may need to replace it.
The soap injector is not getting enough water: If the soap injector is not getting enough water, it will not be able to create a proper soap solution. To fix this, you can try increasing the water pressure or flow rate.
The soap injector is not getting enough soap: If the soap injector is not getting enough soap, it will not be able to create a proper soap solution. To fix this, you can try adding more soap to the tank.
The soap injector is not properly installed: If the soap injector is not properly installed, it may not be able to create a proper soap solution. To fix this, you can try reinstalling the injector according to the manufacturer’s instructions.
How do I clean the soap injector on my Blue Clean pressure washer?
To clean the soap injector on your Blue Clean pressure washer, you will need:
A small brush or needle
A bucket of water
1. Turn off the pressure washer and disconnect the hose from the gun.
2. Remove the soap injector from the gun.
3. Dip the brush or needle into the bucket of water and use it to clean the inside of the soap injector.
4. Rinse the soap injector thoroughly with water.
5. Reattach the soap injector to the gun.
How do I increase the water pressure or flow rate on my Blue Clean pressure washer?
To increase the water pressure or flow rate on your Blue Clean pressure washer, you can try the following:
Turn the pressure washer on and off quickly several times. This will help to clear any blockages in the hose or nozzle.
Increase the pressure setting on the pressure washer.
Open the water valve wider.
Use a longer hose.
How do I add more soap to the tank on my Blue Clean pressure washer?
To add more soap to the tank on your Blue Clean pressure washer, you will need:
The soap bottle
The soap injector
The pressure washer
1. Turn off the pressure washer and disconnect the hose from the gun.
2. Remove the soap injector from the gun.
3. Pour the soap into the tank until it reaches the fill line.
4. Reattach the soap injector to the gun.
5. Connect the hose to the gun and turn on the pressure washer.
How do I properly install the soap injector on my Blue Clean pressure washer?
To properly install the soap injector on your Blue Clean pressure washer, you will need:
The soap injector
The pressure washer
1. Turn off the pressure washer and disconnect the hose from the gun.
2. Remove the old soap injector from the gun.
3. Insert the new soap injector into the gun.
4. Connect the hose to the gun and turn on the pressure washer.
