Bubble Blast Chainsaw Not Working

A bubble blast chainsaw is a powerful tool that can be used for a variety of tasks, from cutting firewood to clearing brush. However, when a bubble blast chainsaw isn’t working properly, it can be a major inconvenience. This guide will help you troubleshoot the most common problems that can cause a bubble blast chainsaw to stop working. By following the steps in this guide, you can quickly diagnose and resolve the problem, so you can get back to using your chainsaw.

Troubleshooting a Bubble Blast Chainsaw

If your bubble blast chainsaw is not working properly, the first step is to identify the problem. Here are some of the most common problems that can cause a bubble blast chainsaw to stop working:

The chainsaw is not getting enough fuel. This can be caused by a clogged fuel filter, a dirty carburetor, or a faulty fuel pump.
The chainsaw is not getting enough air. This can be caused by a clogged air filter or a dirty carburetor.
The spark plug is not firing. This can be caused by a faulty spark plug, a bad spark plug wire, or a loose spark plug connection.
The chainsaw chain is too tight or too loose. This can cause the chainsaw to overheat and malfunction.
The chainsaw chain is dull. A dull chain will not cut through wood efficiently and can cause the chainsaw to overheat.

Once you have identified the problem, you can follow the steps in this guide to troubleshoot and resolve the issue.

Why Bubble Blast Chainsaw Not Working

1. Chain is too loose

If the chain is too loose, it will not be able to grip the wood properly and will cause the chainsaw to stall. To tighten the chain, use the chain tensioner located on the side of the chainsaw. Turn the tensioner clockwise until the chain is snug against the bar.

2. Chain is too tight

If the chain is too tight, it will be difficult to move and will cause the chainsaw to overheat. To loosen the chain, use the chain tensioner located on the side of the chainsaw. Turn the tensioner counterclockwise until the chain is able to move freely.

3. Bar is bent

If the bar is bent, it will cause the chain to skip and will not be able to cut properly. To check if the bar is bent, lay the chainsaw flat on a table and sight down the bar. If the bar is not straight, it will need to be straightened or replaced.

4. Chain is dull

A dull chain will not be able to cut properly and will cause the chainsaw to stall. To sharpen the chain, use a chainsaw file or a chainsaw sharpening tool. Follow the manufacturer’s instructions for sharpening the chain.

5. Spark plug is bad

If the spark plug is bad, it will not be able to create a spark and the chainsaw will not start. To check if the spark plug is bad, remove the spark plug and hold it against the engine block. Crank the engine and look for a spark. If there is no spark, the spark plug will need to be replaced.

6. Fuel filter is clogged

If the fuel filter is clogged, it will restrict the flow of fuel to the engine and the chainsaw will not start. To check if the fuel filter is clogged, remove the fuel filter and inspect it for dirt or debris. If the filter is clogged, it will need to be replaced.

7. Carburetor is dirty

If the carburetor is dirty, it will not be able to mix the fuel and air properly and the chainsaw will not start. To clean the carburetor, remove the carburetor from the chainsaw and disassemble it. Clean the carburetor with carburetor cleaner and reassemble it.

8. Air filter is dirty

If the air filter is dirty, it will restrict the flow of air to the carburetor and the chainsaw will not start. To check if the air filter is dirty, remove the air filter and inspect it for dirt or debris. If the filter is dirty, it will need to be replaced.

9. Oil level is low

If the oil level is low, it will cause the chainsaw to overheat and will not start. To check the oil level, remove the oil fill cap and look at the oil level. The oil level should be between the full and add marks on the dipstick. If the oil level is low, add oil to the chainsaw until the level reaches the full mark.

10. Engine is seized

If the engine is seized, it will not be able to turn over and the chainsaw will not start. To check if the engine is seized, try to turn the engine over by hand. If the engine does not turn over, it will need to be rebuilt or replaced.

How to Troubleshoot: Bubble Blast Chainsaw Not Working

A bubble blast chainsaw is a powerful tool that can be used for a variety of tasks, from cutting firewood to clearing brush. However, like any other tool, bubble blast chainsaws can malfunction from time to time. If your bubble blast chainsaw is not working, there are a few things you can check to troubleshoot the problem.

Step 1: Check the Fuel

The first thing you should check is the fuel level. Make sure that the chainsaw has enough fuel to operate. If the fuel level is low, fill up the tank and try starting the chainsaw again.

Step 2: Check the Spark Plug

If the chainsaw still does not start, the next thing you should check is the spark plug. Remove the spark plug and inspect it for damage. If the spark plug is wet or fouled, clean it or replace it with a new one.

Step 3: Check the Air Filter

The air filter is another important part of a chainsaw that can affect its performance. If the air filter is dirty, it can restrict the flow of air to the carburetor, which can cause the chainsaw to stall or not start at all. To check the air filter, remove it from the chainsaw and inspect it for dirt or debris. If the air filter is dirty, clean it or replace it with a new one.

Step 4: Check the Carburetor

If the chainsaw still does not start after checking the fuel, spark plug, and air filter, the problem may be with the carburetor. The carburetor is responsible for mixing the fuel and air in the correct proportions, so if it is not adjusted properly, the chainsaw will not run correctly. To check the carburetor, you will need to remove it from the chainsaw and take it to a qualified technician.

Step 5: Take the Chainsaw to a Qualified Technician

If you have checked all of the above and the chainsaw still does not start, it is best to take it to a qualified technician. A technician will be able to diagnose the problem and make the necessary repairs.

Conclusion

By following these steps, you can troubleshoot a bubble blast chainsaw that is not working. If you are unable to fix the problem yourself, it is best to take the chainsaw to a qualified technician.

FAQs

Why is my bubble blast chainsaw not working?

There are a few possible reasons why your bubble blast chainsaw might not be working. Here are a few things to check:

Is the chainsaw plugged in? Make sure that the chainsaw is plugged into an outlet and that the outlet is working.
Is the chainsaw turned on? Check the power switch to make sure that it is turned on.
Is the chain oil reservoir full? The chainsaw needs to have enough chain oil in order to function properly. Check the chain oil reservoir and add oil if necessary.
Is the chain dull? A dull chain can make it difficult to cut through wood. Sharpen the chain if necessary.
Is the chainsaw clogged? The chainsaw can become clogged with sawdust and debris. Clean the chainsaw if necessary.

If you have checked all of these things and your chainsaw is still not working, you may need to take it to a professional for repairs.

How do I sharpen the chain on my bubble blast chainsaw?

To sharpen the chain on your bubble blast chainsaw, you will need a chainsaw file.

1. Turn off the chainsaw and disconnect the spark plug wire.
2. Remove the chain from the chainsaw.
3. Hold the file at a 45-degree angle to the chain.
4. File the chain in the direction of the teeth.
5. Repeat steps 3 and 4 until all of the teeth on the chain are sharpened.
6. Reattach the chain to the chainsaw.
7. Test the chainsaw to make sure that the chain is sharp.

How do I change the chain on my bubble blast chainsaw?

To change the chain on your bubble blast chainsaw, you will need a new chain and a chain breaker tool.

1. Turn off the chainsaw and disconnect the spark plug wire.
2. Remove the chain cover.
3. Loosen the chain tensioner bolt.
4. Slide the old chain off of the sprockets.
5. Install the new chain on the sprockets.
6. Tighten the chain tensioner bolt.
7. Reattach the chain cover.

How do I adjust the chain tension on my bubble blast chainsaw?

To adjust the chain tension on your bubble blast chainsaw, you will need a screwdriver.

1. Turn off the chainsaw and disconnect the spark plug wire.
2. Locate the chain tensioner bolt.
3. Use the screwdriver to turn the chain tensioner bolt clockwise to tighten the chain or counterclockwise to loosen the chain.
4. Check the chain tension by pulling on the chain.
5. The chain should have about 1/8 inch of slack.
6. If the chain is too tight or too loose, adjust the chain tensioner bolt accordingly.

What should I do if my bubble blast chainsaw is leaking oil?

If your bubble blast chainsaw is leaking oil, there are a few things you can check:

Is the oil level in the reservoir low? If the oil level is low, add oil to the reservoir until it reaches the full mark.
Is the oil filter clogged? If the oil filter is clogged, it will not be able to filter the oil properly and oil will leak out of the chainsaw. Clean or replace the oil filter if necessary.
Is the oil line damaged? If the oil line is damaged, oil will leak out of the chainsaw. Replace the oil line if necessary.
Is the oil pump damaged? If the oil pump is damaged, it will not be able to pump oil to the chain and oil will leak out of the chainsaw. Repair or replace the oil pump if necessary.

If you have checked all of these things and your chainsaw is still leaking oil, you may need to take it to a professional for repairs.

Next Post to Read: Chainsaw Tensioner Not Working