Craftsman Chainsaw Automatic Oiler Not Working

As a chainsaw owner, there’s nothing more frustrating than having your saw’s automatic oiler stop working. Not only can it lead to damage to the saw’s chain and bar, but it can also be a safety hazard. After all, a dull or damaged chain is more likely to kickback, which can cause serious injury.

If your craftsman chainsaw automatic oiler isn’t working, don’t despair. There are a few simple troubleshooting steps you can take to quickly diagnose and resolve the problem. In this guide, I’ll walk you through the process, highlighting the most common causes of this issue and providing tips on how to fix them.

By the end of this guide, you’ll be able to get your chainsaw’s automatic oiler back up and running in no time, so you can get back to cutting wood without worry.

Why Craftsman Chainsaw Automatic Oiler Not Working

1. Oiler Hose Is Clogged

The oiler hose can become clogged with sawdust or other debris, preventing oil from reaching the chain. To fix this, remove the oiler hose from the chainsaw and clean it with a small brush or wire.

2. Oiler Pump Is Not Working

The oiler pump may be damaged or broken, preventing it from pumping oil to the chain. To check the oiler pump, remove the oiler cover and look for any damage to the pump or its components. If the pump is damaged, it will need to be replaced.

3. Oil Level Is Low

If the oil level in the chainsaw is low, the oiler will not be able to pump enough oil to the chain. To fix this, add oil to the chainsaw until the oil level is between the full and add marks on the oil reservoir.

4. Oiler Switch Is Off

The oiler switch may be turned off, preventing the oiler from pumping oil to the chain. To check the oiler switch, turn it on and make sure that the oiler is pumping oil to the chain.

5. Chainsaw Is Running Too Fast

If the chainsaw is running too fast, the oiler will not be able to keep up with the demand for oil. To fix this, adjust the chainsaw’s throttle so that it is running at a slower speed.

How to Troubleshoot: Craftsman Chainsaw Automatic Oiler Not Working

Symptoms of a Craftsman Chainsaw Automatic Oiler Not Working

There are a few symptoms that can indicate that your Craftsman chainsaw automatic oiler is not working properly. These include:

The chainsaw chain is not being lubricated properly. This can lead to the chain becoming hot and smoking, and can eventually damage the chain and sprockets.
The oil reservoir is not filling up. This can be caused by a blockage in the oil line or a faulty oil pump.
The oiler is making a loud noise. This could be a sign that the oil pump is not working properly.

How to Troubleshoot a Craftsman Chainsaw Automatic Oiler

To troubleshoot a Craftsman chainsaw automatic oiler, you will need to:

1. Inspect the oil reservoir. Make sure that the reservoir is full of oil and that there are no blockages in the oil line. If the reservoir is empty, fill it up with the correct type of oil. If there is a blockage in the oil line, you will need to remove it.
2. Check the oil pump. The oil pump is located on the side of the chainsaw. To check the oil pump, start the chainsaw and listen for a whining noise. If you do not hear a whining noise, the oil pump may be faulty. You can also check the oil pump by removing the oil cap and looking inside. If you see oil flowing out of the pump, the pump is working properly.
3. Replace the oiler. If you have checked the oil reservoir and the oil pump and they are both working properly, the problem may be with the oiler itself. You can try replacing the oiler to see if that fixes the problem.

Preventing Craftsman Chainsaw Automatic Oiler Problems

You can prevent Craftsman chainsaw automatic oiler problems by:

Keeping the oil reservoir full. Make sure that the oil reservoir is always full of oil. This will help to ensure that the chain is properly lubricated and that the oil pump does not become overworked.
Using the correct type of oil. Use the correct type of oil for your chainsaw. The type of oil that you use will depend on the type of chainsaw that you have.
Cleaning the oil line regularly. The oil line can become blocked with dirt and debris. To prevent this, you should clean the oil line regularly.

Conclusion

By following these tips, you can help to troubleshoot and prevent Craftsman chainsaw automatic oiler problems. If you are having trouble troubleshooting the problem yourself, you can always take your chainsaw to a qualified repair technician.

FAQs: Craftsman Chainsaw Automatic Oiler Not Working

Why is my Craftsman chainsaw automatic oiler not working?

There are a few possible reasons why your Craftsman chainsaw automatic oiler may not be working. Here are some of the most common causes:

The oiler is not turned on. Make sure that the oiler is turned on and that the oil tank is full.
The oiler is clogged. The oiler can become clogged with sawdust or other debris, which can prevent the oil from flowing properly. To clean the oiler, remove the oiler cover and clean the inside of the oiler with a small brush.
The oiler is not adjusted properly. The oiler may not be adjusted properly, which can cause the oil to be applied too quickly or too slowly. To adjust the oiler, follow the instructions in the owner’s manual.
The chainsaw is not properly lubricated. If the chainsaw is not properly lubricated, the oiler may not be able to keep up with the demand for oil. To properly lubricate the chainsaw, apply oil to the bar and chain before each use.

How do I fix my Craftsman chainsaw automatic oiler?

To fix your Craftsman chainsaw automatic oiler, you will need to identify the cause of the problem. Once you have identified the cause of the problem, you can follow the steps below to fix it:

If the oiler is not turned on, turn it on and make sure that the oil tank is full.
If the oiler is clogged, remove the oiler cover and clean the inside of the oiler with a small brush.
If the oiler is not adjusted properly, adjust the oiler according to the instructions in the owner’s manual.
If the chainsaw is not properly lubricated, apply oil to the bar and chain before each use.

What are the symptoms of a Craftsman chainsaw automatic oiler that is not working?

The symptoms of a Craftsman chainsaw automatic oiler that is not working can include:

The chainsaw is running hot.
The chainsaw is smoking.
The chainsaw is making a loud noise.
The chainsaw is not cutting through wood as easily as it used to.
The chainsaw bar and chain are becoming dull quickly.

What are the dangers of a Craftsman chainsaw automatic oiler that is not working?

A Craftsman chainsaw automatic oiler that is not working can be dangerous because it can cause the chainsaw to overheat, smoke, or make a loud noise. These problems can all lead to serious injuries. Additionally, a chainsaw that is not properly lubricated can cause the bar and chain to become dull quickly, which can also lead to injuries.

How can I prevent my Craftsman chainsaw automatic oiler from malfunctioning?

To prevent your Craftsman chainsaw automatic oiler from malfunctioning, you can follow these tips:

Always turn on the oiler and make sure that the oil tank is full before using the chainsaw.
Clean the oiler regularly to prevent it from becoming clogged.
Adjust the oiler according to the instructions in the owner’s manual.
Properly lubricate the chainsaw bar and chain before each use.

By following these tips, you can help to ensure that your Craftsman chainsaw automatic oiler works properly and that you stay safe while using your chainsaw.

Next Post to Read: Craftsman Chainsaw Bar Oil Not Working