Power Drill Battery Not Charging Here’s How to Charge it Without a Charger
Your power drill is one of the most important tools in your arsenal, but what happens when the battery dies Don’t panic! You can still charge your drill battery without a charger. In this blog post, we’ll show you how to do just that. We’ll also provide some tips on how to extend the life of your drill battery so you don’t have to deal with this issue again in the future.
So, if your power drill battery is not charging, read on for all the information you need!
How To Charge Power Drill Battery Without Charger
1. Remove the battery from the drill.
2. Connect a USB cable to the battery terminals.
3. Plug the USB cable into a power outlet.
4. The battery will start charging.
5. Once the battery is fully charged, disconnect the USB cable.
6. Reinsert the battery into the drill.
How to Charge a Power Drill Battery Without a Charger
What You Will Need
Power drill battery
AA batteries (4)
Electrical tape
Wire cutters
Multimeter
Steps
1. Remove the battery from the power drill.
2. Take the AA batteries and connect them in series, positive to negative.
3. Wrap the batteries in electrical tape to secure them together.
4. Cut a piece of wire about 6 inches long.
5. Strip the ends of the wire.
6. Connect one end of the wire to the positive terminal of the battery pack.
7. Connect the other end of the wire to the positive terminal of the multimeter.
8. Turn on the multimeter and set it to the DC voltage setting.
9. The multimeter should read a voltage of about 12 volts.
10. Connect the negative terminal of the battery pack to the negative terminal of the multimeter.
11. The multimeter should read a voltage of about 0 volts.
12. Leave the battery pack connected to the multimeter for about 8 hours.
13. After 8 hours, disconnect the battery pack from the multimeter.
14. Reinsert the battery into the power drill.
15. The power drill should now be fully charged.
Tips
Be careful not to short-circuit the battery pack.
Make sure the batteries are in good condition before using them to charge the power drill battery.
Only use AA batteries that are the same size and type.
Do not charge the battery pack for longer than 8 hours.
Do not use the power drill while it is charging.
Warnings
Charging a power drill battery without a charger can be dangerous.
Always follow the safety instructions that come with your power drill.
If you are not comfortable charging the battery pack yourself, take it to a qualified technician.
Also Read: How To Choose A Power Drill
FAQs: How to Charge Power Drill Battery Without Charger
What are the different ways to charge a power drill battery without a charger?
There are a few different ways to charge a power drill battery without a charger. The most common method is to use a car battery. You can also use a portable power bank, a solar charger, or a DIY charger.
How do I use a car battery to charge a power drill battery?
To use a car battery to charge a power drill battery, you will need:
A car battery
A set of jumper cables
A power drill battery
1. Connect the positive terminal of the car battery to the positive terminal of the power drill battery.
2. Connect the negative terminal of the car battery to the negative terminal of the power drill battery.
3. Turn on the car and let it run for about 10 minutes.
4. Disconnect the jumper cables from the car battery and the power drill battery.
The power drill battery should now be charged.
How do I use a portable power bank to charge a power drill battery?
To use a portable power bank to charge a power drill battery, you will need:
A portable power bank
A power drill battery
1. Connect the power drill battery to the portable power bank.
2. Turn on the portable power bank.
3. The power drill battery should now be charging.
The charging time will depend on the capacity of the portable power bank and the power drill battery.
How do I use a solar charger to charge a power drill battery?
To use a solar charger to charge a power drill battery, you will need:
A solar charger
A power drill battery
1. Connect the power drill battery to the solar charger.
2. Place the solar charger in a sunny location.
3. The power drill battery should now be charging.
The charging time will depend on the amount of sunlight available.
How do I make a DIY charger for a power drill battery?
To make a DIY charger for a power drill battery, you will need:
A 12-volt power supply
A 12-volt DC adapter
A power drill battery
1. Connect the positive terminal of the power supply to the positive terminal of the DC adapter.
2. Connect the negative terminal of the power supply to the negative terminal of the DC adapter.
3. Connect the positive terminal of the DC adapter to the positive terminal of the power drill battery.
4. Connect the negative terminal of the DC adapter to the negative terminal of the power drill battery.
The power drill battery should now be charging.
How long does it take to charge a power drill battery?
The charging time for a power drill battery will depend on the capacity of the battery and the charging method.
A battery with a capacity of 1.5 amps will take about 1 hour to charge using a car battery.
A battery with a capacity of 2.0 amps will take about 2 hours to charge using a car battery.
A battery with a capacity of 3.0 amps will take about 3 hours to charge using a car battery.
The charging time for a power drill battery using a portable power bank or a solar charger will vary depending on the capacity of the power bank or solar charger.
The charging time for a DIY charger will vary depending on the power supply and the DC adapter.
