Do you have a Dewalt drill that won’t turn on If so, it may be because the power cord is damaged. Replacing the power cord on a Dewalt drill is a relatively simple task that can be completed in just a few minutes. In this blog post, we will walk you through the steps of .
We’ll start by taking a look at the tools and materials you’ll need. You will need:
A Phillips head screwdriver
A new power cord for your Dewalt drill
Electrical tape
Next, we’ll show you how to remove the old power cord. To do this, you will need to:
1. Unplug the drill from the outlet.
2. Remove the screws that hold the battery housing in place.
3. Remove the battery housing.
4. Locate the power cord and disconnect it from the drill.
5. Remove the old power cord from the drill.
Now that you have removed the old power cord, you can install the new one. To do this, you will need to:
1. Connect the new power cord to the drill.
2. Secure the power cord to the drill with electrical tape.
3. Replace the battery housing.
4. Replace the screws that hold the battery housing in place.
That’s it! You have now successfully replaced the power cord on your Dewalt drill.
How To Replace The Power Cord On A Dewalt Drill
1. Turn off the drill and unplug it from the outlet.
2. Remove the two screws that hold the side cover in place.
3. Remove the side cover.
4. Disconnect the old power cord from the drill.
5. Connect the new power cord to the drill.
6. Reattach the side cover.
7. Replace the two screws.
8. Plug the drill into an outlet and test it to make sure it works properly.
How To Replace The Power Cord On A Dewalt Drill
Tools Needed
Phillips head screwdriver
Wire strippers
Electrical tape
New power cord
Steps
1. Turn off the drill and unplug it from the power outlet.
2. Remove the screws that hold the battery housing in place.
3. Remove the battery housing.
4. Locate the power cord connector.
5. Use the wire strippers to remove the insulation from the ends of the old power cord.
6. Strip about 1 inch of insulation from each end of the new power cord.
7. Twist the bare wires together.
8. Apply electrical tape to the connections to insulate them.
9. Plug the new power cord into the drill.
10. Reattach the battery housing.
11. Replace the screws that hold the battery housing in place.
Tips
Make sure that the new power cord is the same length as the old one.
Be careful not to strip too much insulation from the ends of the power cords.
Make sure that the connections are tight and secure.
Test the drill to make sure that it is working properly.
Also Read: How To Reverse A Power Drill
FAQs: How to Replace the Power Cord on a Dewalt Drill
What tools do I need to replace the power cord on a Dewalt drill?
A Phillips head screwdriver
A wire stripper
A crimping tool
A new power cord
How do I remove the old power cord from my Dewalt drill?
1. Turn off the drill and unplug it from the outlet.
2. Remove the screws that hold the battery cover in place.
3. Remove the battery cover.
4. Locate the two screws that hold the power cord in place.
5. Use the Phillips head screwdriver to remove the screws.
6. Pull the power cord out of the drill.
How do I install the new power cord on my Dewalt drill?
1. Insert the new power cord into the drill.
2. Make sure that the power cord is properly seated in the connector.
3. Use the Phillips head screwdriver to secure the power cord in place.
4. Replace the battery cover.
5. Screw the battery cover in place.
How do I test the new power cord on my Dewalt drill?
1. Plug the drill into an outlet.
2. Turn on the drill.
3. Test the drill to make sure that it is working properly.
What should I do if I have trouble replacing the power cord on my Dewalt drill?
If you have trouble replacing the power cord on your Dewalt drill, you can contact Dewalt customer service for assistance.
