If your Mi-TM pressure washer burner isn’t working, you’re not alone. This is a common problem that can be frustrating and inconvenient. But don’t worry, there’s a good chance you can fix it yourself with a little troubleshooting.
In this guide, I’ll walk you through the steps to troubleshoot a Mi-TM pressure washer burner that isn’t working. I’ll cover everything from common causes of the problem to specific troubleshooting steps. By the end of this guide, you’ll be able to get your pressure washer up and running again in no time.
Why Mi-T-M Pressure Washer Burner Not Working
No Gas Flow
Cause:
The gas valve is not opening.
Solution:
Check the gas valve to make sure it is open. If it is not, open it by turning the knob clockwise.
Blocked Fuel Line
Cause:
The fuel line is blocked by debris.
Solution:
Clean the fuel line by removing the debris.
Bad Gas Filter
Cause:
The gas filter is clogged.
Solution:
Replace the gas filter.
Bad Gas Injector
Cause:
The gas injector is not working properly.
Solution:
Replace the gas injector.
Bad Spark Plug
Cause:
The spark plug is not firing.
Solution:
Replace the spark plug.
Bad CDI Unit
Cause:
The CDI unit is not sending a spark to the spark plug.
Solution:
Replace the CDI unit.
How to Troubleshoot: MI-TM Pressure Washer Burner Not Working
Symptoms
There are a few different symptoms that may indicate that the burner on your MI-TM pressure washer is not working properly. These include:
The pressure washer is not producing any hot water.
The pressure washer is producing only cold water.
The pressure washer is producing water that is not hot enough.
The pressure washer is making a loud noise when it is running.
The pressure washer is smoking.
The pressure washer is emitting a burning smell.
Causes
There are a number of different things that could cause the burner on your MI-TM pressure washer to stop working. These include:
A clogged fuel filter.
A dirty or damaged fuel pump.
A faulty pressure switch.
A faulty burner assembly.
A problem with the electrical wiring.
Troubleshooting
To troubleshoot the problem with your MI-TM pressure washer burner, you will need to first identify the cause of the problem. You can do this by following these steps:
1. Check the fuel filter. If the fuel filter is clogged, it will prevent the fuel from reaching the burner. To check the fuel filter, remove it from the pressure washer and inspect it for any debris. If the fuel filter is clogged, replace it with a new one.
2. Check the fuel pump. The fuel pump is responsible for sending fuel to the burner. If the fuel pump is not working properly, it will not be able to provide enough fuel to the burner. To check the fuel pump, turn on the pressure washer and listen for the fuel pump to run. If you do not hear the fuel pump running, or if the fuel pump is making a loud noise, the fuel pump may be faulty. You will need to replace the fuel pump.
3. Check the pressure switch. The pressure switch is responsible for turning on the burner when the pressure washer reaches a certain pressure. If the pressure switch is not working properly, it will not be able to turn on the burner. To check the pressure switch, turn on the pressure washer and watch the pressure gauge. If the pressure gauge does not increase when you turn on the pressure washer, the pressure switch may be faulty. You will need to replace the pressure switch.
4. Check the burner assembly. The burner assembly is responsible for igniting the fuel and producing the hot water. If the burner assembly is faulty, it will not be able to ignite the fuel. To check the burner assembly, remove it from the pressure washer and inspect it for any damage. If the burner assembly is damaged, you will need to replace it.
5. Check the electrical wiring. The electrical wiring is responsible for sending power to the burner. If the electrical wiring is damaged, it will not be able to provide power to the burner. To check the electrical wiring, inspect the wires for any damage. If the wires are damaged, you will need to replace them.
Solutions
Once you have identified the cause of the problem with your MI-TM pressure washer burner, you can then fix the problem. The solutions for each of the problems are listed below:
Clogged fuel filter:
To fix a clogged fuel filter, simply remove the filter from the pressure washer and replace it with a new one.
Dirty or damaged fuel pump:
To fix a dirty or damaged fuel pump, you will need to remove the fuel pump from the pressure washer and clean or replace it.
Faulty pressure switch:
To fix a faulty pressure switch, you will need to remove the pressure switch from the pressure washer and replace it.
Faulty burner assembly:
To fix a faulty burner assembly, you will need to remove the burner assembly from the pressure washer and replace it.
Problem with the electrical wiring:
To fix a problem with the electrical wiring, you will need to inspect the wires for any damage and replace them if necessary.
Prevention
You can prevent problems with your MI-TM pressure washer burner by following these tips:
Keep the fuel filter clean:
A clogged fuel filter can prevent the fuel from reaching the burner. To keep the fuel filter clean, simply remove it from the pressure washer and rinse it with warm water every few months.
Inspect the fuel pump regularly:
The fuel pump is responsible for sending fuel to the burner. If the fuel pump is not working properly, it will not be able to provide enough fuel to the burner. To inspect the fuel pump, turn on the pressure washer and listen for the fuel pump to run. If you do not hear the fuel pump running, or
Also Read: Workzone Pressure Washer Not Working
FAQs: Mi-T-M Pressure Washer Burner Not Working
Why is my Mi-T-M pressure washer burner not working?
There are a few possible reasons why your Mi-T-M pressure washer burner might not be working. Here are some of the most common causes:
The burner is not getting enough fuel: Make sure that the fuel tank is full and that the fuel line is not kinked or blocked.
The burner is not getting enough air: Check the air filter to make sure that it is clean and free of debris.
The burner is not getting enough spark: Check the spark plug to make sure that it is properly connected and that the gap is correct.
The burner is not properly adjusted: The burner may need to be adjusted to ensure that it is getting the correct amount of fuel and air.
The burner is damaged: If the burner is damaged, it will need to be replaced.
How do I troubleshoot my Mi-T-M pressure washer burner?
If your Mi-T-M pressure washer burner is not working, you can troubleshoot the problem by following these steps:
1. Check the fuel tank: Make sure that the fuel tank is full and that the fuel line is not kinked or blocked.
2. Check the air filter: Remove the air filter and clean it with a clean, dry cloth. If the air filter is dirty, replace it with a new one.
3. Check the spark plug: Remove the spark plug and check the gap. The gap should be between 0.020 and 0.030 inches. If the gap is incorrect, adjust it with a spark plug gap tool.
4. Adjust the burner: The burner may need to be adjusted to ensure that it is getting the correct amount of fuel and air. To adjust the burner, follow the instructions in the owner’s manual.
5. Replace the burner: If the burner is damaged, it will need to be replaced.
How do I clean the burner on my Mi-T-M pressure washer?
To clean the burner on your Mi-T-M pressure washer, you will need:
A soft cloth
A can of compressed air
A degreaser
1. Turn off the pressure washer and disconnect the fuel line:
2. Remove the burner cover:
3. Use the soft cloth to wipe away any dirt or debris from the burner:
4. Use the compressed air to blow away any remaining dirt or debris:
5. Apply the degreaser to the burner and let it sit for a few minutes:
6. Wipe away the degreaser with the soft cloth:
7. Reinstall the burner cover:
How do I replace the burner on my Mi-T-M pressure washer?
To replace the burner on your Mi-T-M pressure washer, you will need:
A new burner
A wrench
A screwdriver
1. Turn off the pressure washer and disconnect the fuel line:
2. Remove the burner cover:
3. Unscrew the old burner from the pressure washer:
4. Screw the new burner onto the pressure washer:
5. Reinstall the burner cover:
6. Reconnect the fuel line:
What are the safety precautions I should take when working on my Mi-T-M pressure washer burner?
When working on your Mi-T-M pressure washer burner, it is important to take the following safety precautions:
Wear safety glasses: Safety glasses will protect your eyes from flying debris.
Wear gloves: Gloves will protect your hands from burns and cuts.
Be careful of hot surfaces: The burner and the exhaust manifold can become very hot. Do not touch them with your bare hands.
Do not work on the pressure washer while it is running: Always turn off the pressure washer and disconnect the fuel line before working on the burner.
Follow the instructions in the owner’s manual: The owner’s manual contains important safety information that you should read before working on the pressure washer.
