Poulan Chainsaw Chain Oiler Not Working

As a chainsaw owner, there are few things more frustrating than having your chain oiler stop working. Not only does it make it difficult to keep your chain sharp and running smoothly, but it can also be dangerous. A dull chain is more likely to kickback, which can cause serious injury.

If your Poulan chainsaw chain oiler isn’t working, there are a few things you can check to try to troubleshoot the problem. In this guide, I’ll walk you through the steps of diagnosing and resolving this common issue.

I’ll start by explaining how the chain oiler works and why it’s important. Then, I’ll discuss the different symptoms of a faulty chain oiler. Finally, I’ll provide step-by-step instructions on how to troubleshoot and repair the problem.

By the end of this guide, you’ll be able to quickly and easily diagnose and resolve any issues with your Poulan chainsaw chain oiler. This will help you keep your chainsaw running smoothly and safely, so you can enjoy using it for years to come.

Why Poulan Chainsaw Chain Oiler Not Working

1. Oiler Hose Clogged

The oiler hose can become clogged with sawdust or other debris, preventing oil from reaching the chain. To clean the oiler hose, remove the hose from the chainsaw and blow it out with compressed air. If the hose is kinked or damaged, it will need to be replaced.

2. Oiler Pump Not Working

The oiler pump can fail due to a number of reasons, including a broken spring, a clogged filter, or a faulty diaphragm. To test the oiler pump, start the chainsaw and listen for the pump to cycle. If you do not hear the pump cycling, the pump may be broken and will need to be replaced.

3. Oil Level Low

If the oil level in the chainsaw is low, the oiler will not be able to deliver enough oil to the chain. To check the oil level, remove the oil cap and look at the oil level. If the oil level is low, add oil to the chainsaw until the level is up to the full mark.

4. Oiler Not Adjusted Properly

The oiler can be adjusted to deliver more or less oil to the chain. If the oiler is not adjusted properly, the chain may not be getting enough oil, or it may be getting too much oil. To adjust the oiler, refer to the owner’s manual for your chainsaw.

5. Chain Too Tight

If the chain is too tight, it can rub against the bar and prevent the oil from reaching the chain. To check the chain tension, loosen the chain tensioner until the chain can be moved up and down about 1/2 inch. If the chain is too loose, tighten the chain tensioner until the chain is snug against the bar.

How to Troubleshoot: Poulan Chainsaw Chain Oiler Not Working

Your Poulan chainsaw is an essential tool for keeping your property clean and well-maintained. But what happens when the chain oiler stops working? This can be a frustrating problem, but it’s usually easy to fix. In this article, we’ll walk you through the steps of troubleshooting a Poulan chainsaw chain oiler that’s not working.

Troubleshooting Steps

1. Check the oil level. The first thing you need to do is check the oil level in the chain oiler reservoir. If the oil level is low, simply add more oil to the reservoir.
2. Check the oil line. The next step is to check the oil line for kinks or blockages. If you find any kinks or blockages, you’ll need to straighten out the line or clear the blockage.
3. Check the oil pump. The oil pump is responsible for sending oil to the chain. If the oil pump is not working properly, it will not be able to send oil to the chain. To check the oil pump, you can do the following:
Turn on the chainsaw and let it run for a few minutes.
While the chainsaw is running, look at the oil line. If you see oil flowing through the line, the oil pump is working properly.
If you do not see oil flowing through the line, the oil pump is not working properly. You will need to replace the oil pump.
4. Check the oil filter. The oil filter helps to keep dirt and debris out of the oil system. If the oil filter is clogged, it will not be able to filter the oil properly. To check the oil filter, you can do the following:
Remove the oil filter from the chainsaw.
Look at the oil filter. If you see dirt or debris on the filter, the filter is clogged. You will need to replace the oil filter.
5. Check the oil cap. The oil cap is designed to keep dirt and debris out of the oil system. If the oil cap is loose or damaged, it will not be able to keep dirt and debris out of the oil system. To check the oil cap, you can do the following:
Make sure that the oil cap is tightly screwed on.
Look at the oil cap for cracks or damage. If the oil cap is cracked or damaged, you will need to replace it.

Conclusion

Troubleshooting a Poulan chainsaw chain oiler that’s not working is usually a simple process. By following the steps in this article, you can quickly and easily get your chainsaw back up and running.

FAQs

1. Why is my Poulan chainsaw chain oiler not working?

The chain oiler may not be working due to a clogged oil hole
a faulty oil pump
or a blocked oil filter. It’s important to inspect and clean these components regularly to ensure proper lubrication of the chain.

2. How can I troubleshoot the oiler on my Poulan chainsaw?

To troubleshoot the oiler
start by checking the oil level and ensuring that the oil tank and oil lines are free from debris. Additionally
inspect the oil pump and the oil delivery system for any malfunctions or blockages.

3. What type of oil should I use for my Poulan chainsaw chain oiler?

It’s recommended to use a high-quality bar and chain oil specifically designed for chainsaws. Avoid using motor oil or other substitutes
as they may not provide sufficient lubrication and can lead to damage.

4. How often should I maintain the chain oiler on my Poulan chainsaw?

Regular maintenance of the chain oiler is essential. It’s advisable to inspect and clean the oiler system after each use
and to perform a more thorough maintenance check at regular intervals as recommended in the chainsaw’s manual.

5. Can a Poulan chainsaw work without the chain oiler?

No
it is not recommended to operate a Poulan chainsaw without a functioning chain oiler. Proper lubrication from the oiler is crucial for the safe and efficient operation of the chainsaw
as it reduces friction and heat generated during cutting.

Next Post to Read: Poulan Pro Chainsaw Oiler Not Working