Poulan Chainsaw Oil Pump Not Working

As a chainsaw owner, there are few things more frustrating than having your saw’s oil pump stop working. Not only is it dangerous to operate a chainsaw without proper lubrication, but it can also lead to costly repairs. If your Poulan chainsaw’s oil pump is not working, there are a few things you can check to try to fix the problem. In this guide, I will walk you through the steps of troubleshooting a Poulan chainsaw oil pump problem. I will also provide tips on how to prevent this issue from happening in the future.

Most Common Reasons Of Poulan Chainsaw Oil Pump Not Working

Poulan Chainsaw Oil Pump Not Working: Causes

Clogged oil filter. The oil filter is located on the bottom of the chainsaw, and it helps to keep the oil pump clean. If the filter becomes clogged, it can restrict the flow of oil to the chain, causing the oil pump to not work properly.
Low oil level. The oil pump needs a certain amount of oil to work properly. If the oil level is too low, the pump will not be able to create enough pressure to push the oil to the chain.
Damaged oil pump. The oil pump is a mechanical device, and it can be damaged if it is not used properly or if it is exposed to excessive vibration. If the oil pump is damaged, it will not be able to pump oil to the chain.
Incorrect oil type. The oil pump is designed to work with a specific type of oil. If you use the wrong type of oil, it can damage the pump and prevent it from working properly.
Clogged oil line. The oil line is the tube that connects the oil pump to the chain. If the oil line becomes clogged, it can restrict the flow of oil to the chain, causing the oil pump to not work properly.
Defective oil pump switch. The oil pump switch is a small electrical switch that turns the oil pump on and off. If the switch is defective, it can prevent the oil pump from working properly.

How to Fix a Poulan Chainsaw Oil Pump

If your Poulan chainsaw oil pump is not working, you can try to fix it yourself by following these steps:

1. Check the oil filter. Remove the oil filter and inspect it for signs of clogging. If the filter is clogged, clean it or replace it with a new one.
2. Check the oil level. Make sure that the oil level is at the correct level. If the oil level is too low, add more oil to the chainsaw.
3. Inspect the oil pump. Look for signs of damage to the oil pump. If the oil pump is damaged, you will need to replace it.
4. Check the oil type. Make sure that you are using the correct type of oil for your chainsaw. If you are using the wrong type of oil, it can damage the oil pump and prevent it from working properly.
5. Check the oil line. Inspect the oil line for signs of clogging. If the oil line is clogged, clean it or replace it with a new one.
6. Check the oil pump switch. Test the oil pump switch to make sure that it is working properly. If the switch is defective, you will need to replace it.

How to Troubleshoot: Poulan Chainsaw Oil Pump Not Working

Symptoms of a Poulan Chainsaw Oil Pump Not Working

There are a few signs that your Poulan chainsaw oil pump may not be working properly. These include:

The chainsaw is running hot, even when it is not under load.
The chainsaw is smoking or making a strange noise.
The chainsaw is losing power.
The chainsaw’s chain is not getting lubricated properly.

If you notice any of these symptoms, it is important to troubleshoot the problem as soon as possible to prevent further damage to your chainsaw.

How to Troubleshoot a Poulan Chainsaw Oil Pump

To troubleshoot a Poulan chainsaw oil pump, you will need to:

1. Inspect the oil pump for damage.
2. Check the oil level in the chainsaw.
3. Clean the oil pump screen.
4. Replace the oil pump.

Inspect the oil pump for damage.

The first step in troubleshooting a Poulan chainsaw oil pump is to inspect it for damage. Look for cracks, leaks, or other damage that could be causing the pump to malfunction. If you find any damage, you will need to replace the oil pump.

Check the oil level in the chainsaw.

The next step is to check the oil level in the chainsaw. If the oil level is low, it could be causing the oil pump to malfunction. To check the oil level, remove the oil cap and look at the oil level indicator. The oil level should be between the full and add marks on the indicator. If the oil level is low, add oil to the chainsaw until the level reaches the full mark.

Clean the oil pump screen.

If the oil level is correct and the oil pump is not damaged, the next step is to clean the oil pump screen. The oil pump screen is located on the bottom of the chainsaw housing. To clean the oil pump screen, remove the oil cap and the oil tank. Then, use a small brush to clean the screen. Be careful not to damage the screen.

Replace the oil pump.

If you have checked the oil level, cleaned the oil pump screen, and the oil pump is still not working, you will need to replace the oil pump. To replace the oil pump, you will need to:

1. Remove the old oil pump.
2. Install the new oil pump.
3. Add oil to the chainsaw.

Removing the old oil pump

To remove the old oil pump, you will need to:

1. Remove the oil cap.
2. Remove the oil tank.
3. Remove the oil pump mounting screws.
4. Remove the oil pump.

Installing the new oil pump

To install the new oil pump, you will need to:

1. Apply a thin coat of oil to the gasket of the new oil pump.
2. Align the oil pump with the mounting holes in the chainsaw housing.
3. Insert the oil pump mounting screws and tighten them until they are snug.
4. Add oil to the chainsaw.

Adding oil to the chainsaw

To add oil to the chainsaw, you will need to:

1. Remove the oil cap.
2. Add oil to the chainsaw until the level reaches the full mark on the oil level indicator.
3. Replace the oil cap.

Troubleshooting Tips

Here are a few tips for troubleshooting a Poulan chainsaw oil pump:

If you are not sure how to troubleshoot a Poulan chainsaw oil pump, you can consult the owner’s manual.
If you are unable to troubleshoot the problem yourself, you can take the chainsaw to a qualified service center.
When troubleshooting a Poulan chainsaw oil pump, it is important to be careful not to damage the chainsaw.

Conclusion

By following these steps, you can troubleshoot a Poulan chainsaw oil pump and get your chainsaw back up and running in no time.

FAQs: Poulan Chainsaw Oil Pump Not Working

Why is my Poulan chainsaw oil pump not working?

There are a few possible reasons why your Poulan chainsaw oil pump may not be working. Here are some of the most common causes:

The oil pump is clogged. The oil pump can become clogged with dirt, sawdust, or other debris, which can prevent it from pumping oil to the chainsaw chain. To clean the oil pump, you can use a small brush or a toothpick to remove any debris that is blocking the pump.
The oil pump is not getting enough oil. The oil pump needs a steady supply of oil in order to work properly. If the oil level in the chainsaw is low, the pump may not be able to draw enough oil to lubricate the chain. To check the oil level, remove the oil cap and look at the oil level indicator. If the oil level is low, add more oil to the chainsaw.
The oil pump is damaged. The oil pump can be damaged if it is dropped or struck. If the oil pump is damaged, it will need to be replaced.

How do I fix a Poulan chainsaw oil pump that is not working?

To fix a Poulan chainsaw oil pump that is not working, you will need to identify the cause of the problem. Once you have identified the cause of the problem, you can take the following steps to fix it:

If the oil pump is clogged, clean it with a small brush or a toothpick.
If the oil pump is not getting enough oil, add more oil to the chainsaw.
If the oil pump is damaged, replace it.

How often should I oil my Poulan chainsaw?

You should oil your Poulan chainsaw every time you use it. This will help to keep the chainsaw chain lubricated and prevent it from overheating. To oil the chainsaw chain, apply a few drops of oil to the bar and chain.

What kind of oil should I use for my Poulan chainsaw?

You should use a high-quality chainsaw oil for your Poulan chainsaw. Chainsaw oil is designed to withstand high temperatures and prevent the chain from rusting. You can find chainsaw oil at most hardware stores.

What happens if I don’t oil my Poulan chainsaw?

If you don’t oil your Poulan chainsaw, the chain will not be lubricated and it will start to overheat. Overheating can damage the chain and the chainsaw itself. It can also be dangerous, as the chain may become hot enough to cause a fire.

Next Post You May Like: Poulan Chainsaw Primer Bulb Not Working