Your Chainsaw Chain Won’t Move Here’s Why and What to Do
Your chainsaw is a powerful tool that can be used for a variety of tasks, from cutting down trees to trimming branches. But what happens when your chainsaw chain won’t move This can be a frustrating problem, but it’s usually easy to fix.
In this blog post, we’ll discuss the most common reasons why your chainsaw chain won’t move and what you can do to fix it. We’ll also provide some tips for preventing this problem from happening in the future.
So if your chainsaw chain is stuck, don’t despair! Read on to learn how to get it moving again.
Why Won’T My Chainsaw Chain Move
There are a few reasons why your chainsaw chain might not be moving.
The chain is too loose:
If the chain is too loose, it will not be able to grip the guide bar and will therefore not move. To tighten the chain, follow the instructions in your chainsaw owner’s manual.
The chain is too tight:
If the chain is too tight, it will bind on the guide bar and will not be able to move. To loosen the chain, follow the instructions in your chainsaw owner’s manual.
The chainsaw is not getting enough oil:
If the chainsaw is not getting enough oil, the chain will become dry and will not be able to move smoothly. To check the oil level, follow the instructions in your chainsaw owner’s manual. If the oil level is low, add oil to the chainsaw.
The chainsaw is not being used properly:
If the chainsaw is not being used properly, it may not be able to move properly. To use the chainsaw properly, follow the instructions in your chainsaw owner’s manual.
Why Won’t My Chainsaw Chain Move?
There are a few reasons why your chainsaw chain might not be moving.
The chain is too tight:
If the chain is too tight, it will bind against the bar and prevent it from moving. To check the chain tension, follow these steps:
Turn off the chainsaw and let it cool down.
Loosen the bar nuts.
Use a chainsaw chain gauge to measure the chain tension. The correct tension will vary depending on the type of chainsaw you have, but it should be between 0.030 and 0.050 inches.
If the chain is too tight, loosen the bar nuts and adjust the chain tension.
Tighten the bar nuts and recheck the chain tension.
The chain is too loose:
If the chain is too loose, it will come off the bar and prevent it from moving. To check the chain tension, follow these steps:
Turn off the chainsaw and let it cool down.
Loosen the bar nuts.
Use a chainsaw chain gauge to measure the chain tension. The correct tension will vary depending on the type of chainsaw you have, but it should be between 0.030 and 0.050 inches.
If the chain is too loose, tighten the bar nuts and adjust the chain tension.
Tighten the bar nuts and recheck the chain tension.
The chain is damaged:
If the chain is damaged, it may not be able to move properly. Here are some common signs of a damaged chain:
The chain is missing links.
The chain is bent or twisted.
The chain is dull.
The chain is rusty.
The chain is cracked.
The chain is stretched.
If you think your chain is damaged, you should replace it with a new one.
The bar is damaged:
If the bar is damaged, it may not be able to support the chain properly. Here are some common signs of a damaged bar:
The bar is bent or twisted.
The bar is cracked.
The bar is worn out.
The bar is rusted.
If you think your bar is damaged, you should replace it with a new one.
The sprocket is damaged:
The sprocket is the part of the chainsaw that drives the chain. If the sprocket is damaged, it may not be able to turn the chain properly. Here are some common signs of a damaged sprocket:
The sprocket is bent or twisted.
The sprocket is cracked.
The sprocket is worn out.
The sprocket is rusted.
If you think your sprocket is damaged, you should replace it with a new one.
The clutch is damaged:
The clutch is the part of the chainsaw that engages and disengages the chain. If the clutch is damaged, it may not be able to engage the chain properly. Here are some common signs of a damaged clutch:
The clutch is not engaging the chain.
The clutch is slipping.
The clutch is making a grinding noise.
If you think your clutch is damaged, you should take your chainsaw to a qualified technician for repairs.
How to Fix a Chainsaw Chain That Won’t Move
If you’ve determined that the cause of your chainsaw chain not moving is something that you can fix yourself, here are the steps to take:
1. Turn off the chainsaw and let it cool down:
2. Loosen the bar nuts:
3. Adjust the chain tension:
4. Tighten the bar nuts:
5. Start the chainsaw and test the chain:
If the chain is still not moving properly, you may need to replace the chain, bar, sprocket, or clutch.
Preventing Chainsaw Chain Problems
You can prevent chainsaw chain problems by following these tips:
Keep the chain properly tensioned:
Inspect the chain regularly for damage:
Replace the chain when it is worn out:
Replace the bar when it is worn out:
Replace the sprocket when it is worn out:
Keep the clutch clean and lubricated:
By following these tips, you can help to ensure that your chainsaw chain stays in good working order and that you can enjoy your chainsaw safely and without any problems.
Also Read THis: Why Won’T My Chainsaw Chain Tighten
FAQs: Why Won’t My Chainsaw Chain Move?
Why won’t my chainsaw chain move when I pull the starter?
There are a few possible reasons why your chainsaw chain might not be moving when you pull the starter.
The chain is too tight: If the chain is too tight, it can bind up and prevent the engine from turning over. To check the chain tension, release the chain tensioner and let the chain fall slack. The chain should be able to move freely up and down the bar. If it is not, tighten the chain tensioner until it is just snug.
The chain is too loose: If the chain is too loose, it can jump off the bar and cause damage to the engine. To check the chain tension, release the chain tensioner and let the chain fall slack. The chain should be able to move freely up and down the bar, but it should not be so loose that it falls off the bar. If it is, tighten the chain tensioner until it is just snug.
The clutch is not engaging: The clutch is responsible for engaging the chain with the engine. If the clutch is not engaging, the chain will not move when you pull the starter. To check the clutch, turn the chainsaw on and let it run for a few seconds. Then, try to move the chain by hand. If the chain does not move, the clutch is not engaging. You will need to take the chainsaw to a qualified service center to have the clutch repaired or replaced.
The engine is not getting enough fuel: If the engine is not getting enough fuel, it will not be able to turn over and the chain will not move. To check the fuel level, remove the fuel cap and look inside the tank. The tank should be at least half full. If it is not, fill the tank with fresh fuel.
The spark plug is not firing: If the spark plug is not firing, the engine will not be able to turn over and the chain will not move. To check the spark plug, remove it from the engine and look at the electrode. The electrode should be clean and free of deposits. If it is not, clean the spark plug with a wire brush and reinstall it.
Why won’t my chainsaw chain move when I push the throttle?
There are a few possible reasons why your chainsaw chain might not be moving when you push the throttle.
The chain is too tight: If the chain is too tight, it can bind up and prevent the engine from turning over. To check the chain tension, release the chain tensioner and let the chain fall slack. The chain should be able to move freely up and down the bar. If it is not, tighten the chain tensioner until it is just snug.
The chain is too loose: If the chain is too loose, it can jump off the bar and cause damage to the engine. To check the chain tension, release the chain tensioner and let the chain fall slack. The chain should be able to move freely up and down the bar, but it should not be so loose that it falls off the bar. If it is, tighten the chain tensioner until it is just snug.
The clutch is not engaging: The clutch is responsible for engaging the chain with the engine. If the clutch is not engaging, the chain will not move when you push the throttle. To check the clutch, turn the chainsaw on and let it run for a few seconds. Then, try to move the chain by hand. If the chain does not move, the clutch is not engaging. You will need to take the chainsaw to a qualified service center to have the clutch repaired or replaced.
The engine is not getting enough fuel: If the engine is not getting enough fuel, it will not be able to turn over and the chain will not move. To check the fuel level, remove the fuel cap and look inside the tank. The tank should be at least half full. If it is not, fill the tank with fresh fuel.
The spark plug is not firing: If the spark plug is not firing, the engine will not be able to turn over and the chain will not move. To check the spark plug, remove it from the engine and look at the electrode. The electrode should be clean and free of deposits. If it is not, clean the spark plug with a wire brush and reinstall it.
Why won’t my chainsaw chain move when I push the bar forward?
There are a few possible reasons why your chainsaw chain might not be moving when you push the bar forward.
The chain is too tight: If the chain is too tight, it
