Your Worx electric chainsaw is a powerful and versatile tool, but it can be frustrating when the chain keeps coming off. There are a few common reasons why this might happen, and fortunately, they’re all relatively easy to fix.
In this blog post, we’ll discuss the most common causes of a chainsaw chain coming off, and we’ll provide step-by-step instructions on how to fix each problem. By the end of this post, you’ll be able to keep your Worx chainsaw running smoothly and safely.
So Worx Electric Chainsaw Chain Keeps Coming Off
Worx Electric Chainsaw Chain Keeps Coming Off: How to Fix It
If the chain on your Worx electric chainsaw keeps coming off, there are a few things you can check to fix the problem.
Check the chain tension:
The chain should be tight enough so that it doesn’t come off, but not so tight that it’s difficult to turn the chainsaw. To check the tension, hold the chainsaw with the chain off the ground and pull up on the chain with your hand. The chain should move up about 1/2 inch. If it doesn’t, tighten the chain tensioner.
Make sure the chain is properly aligned:
The chain should be aligned with the guide bar so that it runs smoothly. If the chain is misaligned, it can come off easily. To align the chain, loosen the bar nuts and slide the guide bar back and forth until the chain is centered. Tighten the bar nuts to secure the guide bar in place.
Clean and lubricate the chainsaw:
A dirty or dry chain can also cause it to come off. Make sure to clean the chainsaw regularly and apply a light coat of oil to the chain before each use.
By following these steps, you can usually fix a Worx electric chainsaw chain that keeps coming off.
Worx Electric Chainsaw Chain Keeps Coming Off
What Causes the Chain to Come Off?
There are a few possible reasons why the chain on your Worx electric chainsaw might keep coming off.
The chain is too loose:
If the chain is too loose, it will be more likely to come off the sprocket. To tighten the chain, follow the instructions in your owner’s manual.
The chain is too tight:
If the chain is too tight, it will be difficult to turn the chainsaw and the chain may come off. To loosen the chain, follow the instructions in your owner’s manual.
The sprocket is worn out:
If the sprocket is worn out, it will not grip the chain properly and the chain may come off. To replace the sprocket, you will need to take your chainsaw to a qualified repair shop.
The guide bar is damaged:
If the guide bar is damaged, it will not support the chain properly and the chain may come off. To replace the guide bar, you will need to take your chainsaw to a qualified repair shop.
How to Fix the Chain Coming Off
Once you have determined the cause of the problem, you can fix the chain coming off by following these steps:
1. Tighten the chain:
If the chain is too loose, tighten it according to the instructions in your owner’s manual.
2. Loosen the chain:
If the chain is too tight, loosen it according to the instructions in your owner’s manual.3. Replace the sprocket:
If the sprocket is worn out, replace it with a new one.
4. Replace the guide bar:
If the guide bar is damaged, replace it with a new one.
Preventing the Chain from Coming Off
To prevent the chain from coming off, you can take the following steps:
Keep the chain properly lubricated:
A well-lubricated chain will be less likely to come off.
Inspect the chain regularly:
Inspect the chain for wear and tear and replace it if necessary.
Avoid over-tightening the chain:
Over-tightening the chain can damage the sprocket and the guide bar.
Avoid under-tightening the chain:
Under-tightening the chain can cause the chain to come off.
By following these tips, you can help to prevent the chain on your Worx electric chainsaw from coming off.
Also Read THis: Worx Electric Chainsaw Not Working
FAQs: Worx Electric Chainsaw Chain Keeps Coming Off
Why is the chain on my Worx electric chainsaw coming off?
There are a few possible reasons why the chain on your Worx electric chainsaw might be coming off.
The chain is too loose: If the chain is too loose, it can easily jump off the sprockets. To tighten the chain, follow the instructions in your chainsaw’s owner’s manual.
The chain is worn out: If the chain is worn out, it can become loose and fall off. To check if the chain is worn out, inspect it for any damage or wear. If the chain is damaged or worn out, you will need to replace it.
The sprockets are worn out: If the sprockets are worn out, they can no longer grip the chain properly, which can cause the chain to jump off. To check if the sprockets are worn out, inspect them for any damage or wear. If the sprockets are damaged or worn out, you will need to replace them.
The chain oil is low: If the chain oil is low, the chain will not be lubricated properly, which can cause it to become hot and jump off. To check the chain oil level, refer to your chainsaw’s owner’s manual. If the chain oil level is low, you will need to add more oil.
How do I tighten the chain on my Worx electric chainsaw?
To tighten the chain on your Worx electric chainsaw, follow these steps:
1. Turn off the chainsaw and disconnect the spark plug wire.
2. Locate the chain tensioner. The chain tensioner is usually located on the side of the chainsaw, near the chain sprocket.
3. Use the chain tensioner tool to turn the tensioner clockwise. This will tighten the chain.
4. Check the chain tension. The chain should be snug against the guide bar, but not so tight that it is difficult to turn.
5. Reattach the spark plug wire and start the chainsaw.
How do I know if the chain on my Worx electric chainsaw is worn out?
To check if the chain on your Worx electric chainsaw is worn out, inspect it for any damage or wear. Look for:
Missing or damaged teeth
A dull cutting edge
A stretched chain
A warped or bent chain
If you see any of these signs, the chain is worn out and needs to be replaced.
How do I replace the sprockets on my Worx electric chainsaw?
To replace the sprockets on your Worx electric chainsaw, follow these steps:
1. Turn off the chainsaw and disconnect the spark plug wire.
2. Remove the chain guard.
3. Remove the old sprockets.
4. Install the new sprockets.
5. Reinstall the chain guard.
6. Reattach the spark plug wire and start the chainsaw.
How do I add chain oil to my Worx electric chainsaw?
To add chain oil to your Worx electric chainsaw, follow these steps:
1. Turn off the chainsaw and disconnect the spark plug wire.
2. Locate the chain oil reservoir. The chain oil reservoir is usually located on the side of the chainsaw, near the chain sprocket.
3. Remove the oil filler cap.
4. Add chain oil to the reservoir until it reaches the fill line.
5. Replace the oil filler cap.
6. Reattach the spark plug wire and start the chainsaw.
