If your Karcher K3 pressure washer is not working, here are a few things to check
Is the pressure washer plugged in and turned on?
Is the water turned on to the pressure washer?
Is the pressure washer switch set to the correct setting?
Is the pressure washer nozzle clogged?
Is the pressure washer pump damaged?
If your Karcher K2 pressure washer is not working, it may be due to a number of reasons. Here are a few common causes and solutions
No water coming out Check the water supply to make sure it is turned on and that the pressure washer is connected to the hose.
Low pressure Check the pressure washer’s pressure gauge to make sure it is within the normal range. If the pressure is low, you may need to clean the filter or replace the pump.
Nozzle not working Make sure the nozzle is properly attached to the pressure washer and that it is not clogged.
If your Karcher 330 pressure washer is not working, here are a few things to check
Is the pressure washer plugged in and turned on?
Is the water turned on to the pressure washer?
Is the pressure washer switch set to On?
Is the pressure washer nozzle clogged?
If your Husky pressure washer pump is not working, it could be due to a number of reasons. Here are a few common causes and solutions
Dirty filter The most common cause of a pressure washer pump not working is a dirty filter. To fix this, remove the filter and clean it with warm, soapy water.
Clogged nozzle Another common cause is a clogged nozzle. To fix this, remove the nozzle and clean it with a small wire brush.
Low pressure If the pressure washer is not producing enough pressure, it could be due to a leak. Check all of the connections for leaks and tighten them as needed.
Faulty pump If the pump is not working at all, it could be faulty. In this case, you will need to replace the pump.
High pressure washer not working
Check the power supply.
Check the water supply.
Check the hoses for leaks.
Check the spray nozzle for clogs.
Clean the filter.
Greenworks electric pressure washer not working. Possible causes
Power cord not plugged in
Pressure washer switch is turned off
Debris blocking the water inlet
Water pump is damaged
If the soap injector on your Generac pressure washer is not working, check the following 1. Make sure the soap tank is filled with soap. 2. Check the hose for kinks or blockages. 3. Make sure the injector is turned on. 4. Clean the injector if it is clogged.
Ferrex pressure washer not working
If your Ferrex pressure washer is not working, here are a few things to check
Make sure that the water supply is turned on and that the pressure washer is connected to a water source.
Check the hose for kinks or blockages.
Make sure that the pressure washer is turned on and that the trigger is pulled.
Check the oil level and add oil if necessary.
If the pressure washer is still not working, contact a qualified technician for help.
If your DeWalt pressure washer pump is not working, it could be due to a number of reasons. Here are a few things to check
Is the pump plugged in? Make sure that the pump is plugged into an outlet and that the outlet is working.
Is the pressure switch turned on? The pressure switch is located on the back of the pump. Make sure that it is turned on.
Is the pump primed? Priming the pump ensures that there is water flowing through the pump before you turn it on. To prime the pump, turn on the water supply to the pump and open the trigger on the gun. Hold the trigger open until you see water coming out of the gun.
Is the pump filter clogged? The pump filter is located on the bottom of the pump. If it is clogged, it will prevent water from flowing through the pump. To clean the filter, remove it from the pump and rinse it under water.
If your Craftsman electric pressure washer is not working, here are a few things to check
Make sure the unit is plugged in and turned on.
Check the water supply to make sure it is turned on and flowing.
Check the pressure washer’s hose for kinks or leaks.
Clean the pressure washer’s filter.
Inspect the pressure washer’s pump for damage.