Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

As a chainsaw owner, there are few things more frustrating than having your bar oiler stop working. Not only does it make it difficult to keep your chain sharp and running smoothly, but it can also be dangerous. A dull chain is more likely to kickback, which can cause serious injury.

If your Husqvarna 455 Rancher bar oiler isn’t working, don’t despair. There are a few simple troubleshooting steps you can take to identify and resolve the problem. In this guide, I’ll walk you through the process of diagnosing and repairing a malfunctioning bar oiler. By the end of this guide, you’ll be able to get your chainsaw back up and running in no time.

What is the bar oiler

The bar oiler is a small pump that delivers oil to the chain as it travels through the guide bar. This oil helps to lubricate the chain and keep it running smoothly. If the bar oiler isn’t working properly, the chain will become dry and start to wear out quickly.

Symptoms of a malfunctioning bar oiler

There are a few common symptoms that indicate that your bar oiler may not be working properly. These include:

The chain is dry and starting to wear out.
The bar oil reservoir is empty or low.
You can hear the bar oiler pump running, but no oil is coming out.
The oil is coming out of the bar oiler in a steady stream, rather than a fine mist.

Most Common Reasons Of Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

Dirty Oiler Tube

The oiler tube on a chainsaw is responsible for delivering oil to the chain, and if it becomes clogged with dirt or debris, it can prevent the chain from getting enough oil and lead to wear and tear. To clean the oiler tube, remove the spark plug and pour a small amount of solvent into the cylinder. Then, turn the engine over a few times to coat the cylinder walls with solvent. Next, use a small brush to clean out the oiler tube. Be sure to wear gloves and eye protection when cleaning the oiler tube.

Blocked Oiler Orifice

The oiler orifice is a small hole in the bar that allows oil to flow to the chain. If this hole becomes blocked, it can prevent oil from reaching the chain. To clean the oiler orifice, use a small pick or needle to clear away any debris. Be careful not to damage the orifice.

Incorrect Oil Viscosity

The oil used in a chainsaw should be the correct viscosity for the temperature at which it will be used. If the oil is too thick, it will not flow easily through the oiler system and reach the chain. If the oil is too thin, it will evaporate quickly and not provide adequate lubrication. The recommended oil viscosity for a Husqvarna Chainsaw 455 Rancher is 10W-30.

Low Oil Level

If the oil level in the chainsaw is too low, the oiler will not be able to deliver enough oil to the chain. To check the oil level, remove the oil cap and look at the oil level indicator. The oil level should be between the full and add marks. If the oil level is low, add oil to the chainsaw until the level reaches the full mark.

Defective Oiler

In rare cases, the oiler on a chainsaw can malfunction. If the oiler is not working properly, it will not be able to deliver oil to the chain. To test the oiler, start the chainsaw and let it run for a few minutes. Then, check the oiler tube and orifice for oil. If there is no oil, the oiler is probably defective and will need to be replaced.

How to Troubleshoot: Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

Symptoms of a Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

There are a few symptoms that you can look for to determine if the bar oiler on your Husqvarna Chainsaw 455 Rancher is not working properly. These include:

The bar oil level is low or empty.
The bar oiler is not pumping oil to the bar.
The bar oil is not flowing freely from the bar oiler.
The bar oil is leaking from the bar oiler.

Troubleshooting a Husqvarna Chainsaw 455 Rancher Bar Oiler

If you are experiencing any of the symptoms listed above, you can troubleshoot the bar oiler by following these steps:

1. Check the bar oil level. The first thing you should do is check the bar oil level. To do this, remove the bar oil cap and look inside the bar oil tank. The bar oil level should be between the full and add marks on the tank. If the bar oil level is low or empty, you will need to add more bar oil to the tank.
2. Check the bar oiler pump. The next thing you should do is check the bar oiler pump. To do this, start the chainsaw and let it run for a few minutes. While the chainsaw is running, look at the bar oiler pump. The pump should be pumping oil to the bar. If you do not see any oil coming from the pump, the pump may be faulty and will need to be replaced.
3. Check the bar oil line. The next thing you should do is check the bar oil line. To do this, follow the bar oil line from the bar oil tank to the bar. Look for any leaks in the line. If you find a leak, you will need to repair or replace the line.
4. Check the bar oil nozzle. The final thing you should do is check the bar oil nozzle. To do this, remove the bar oil cap and look at the bar oil nozzle. The nozzle should be clear and free of debris. If the nozzle is clogged, you will need to clean it.

How to Fix a Husqvarna Chainsaw 455 Rancher Bar Oiler

If you have determined that the bar oiler on your Husqvarna Chainsaw 455 Rancher is not working properly, you can fix it by following these steps:

1. Add more bar oil to the tank. If the bar oil level is low or empty, you will need to add more bar oil to the tank. To do this, remove the bar oil cap and add bar oil to the tank until the level is between the full and add marks on the tank.
2. Replace the bar oiler pump. If the bar oiler pump is faulty, you will need to replace it. To do this, remove the old pump and install the new pump. Be sure to follow the manufacturer’s instructions for installation.
3. Replace the bar oil line. If the bar oil line is leaking, you will need to replace it. To do this, remove the old line and install the new line. Be sure to follow the manufacturer’s instructions for installation.
4. Clean the bar oil nozzle. If the bar oil nozzle is clogged, you will need to clean it. To do this, remove the bar oil cap and use a small brush to clean the nozzle. Be sure to clean the nozzle thoroughly.

Preventing Problems with Your Husqvarna Chainsaw 455 Rancher Bar Oiler

You can help prevent problems with your Husqvarna Chainsaw 455 Rancher bar oiler by following these tips:

Keep the bar oil level full. Make sure to keep the bar oil level full at all times. This will help to ensure that the bar oiler is working properly.
Change the bar oil regularly. You should change the bar oil regularly, according to the manufacturer’s recommendations. This will help to keep the bar oil clean and free of debris.
Inspect the bar oiler regularly. Inspect the bar oiler regularly for leaks or other problems. This will help to catch problems early on and prevent them from becoming more serious.

By following these tips, you can help to keep your Husqvarna Chainsaw 455 Rancher bar oiler working properly.

FAQs

Why is the bar oiler on my Husqvarna 455 Rancher not working?

There are a few possible reasons why the bar oiler on your Husqvarna 455 Rancher may not be working.

The oil level is low. Check the oil level in the reservoir and add oil if necessary.
The oil line is clogged. Clean the oil line to ensure that oil is flowing freely to the bar and chain.
The oil pump is not working properly. If the oil pump is not working, it will need to be replaced.
The bar oiler switch is turned off. Make sure that the bar oiler switch is turned on.

How do I adjust the bar oiler on my Husqvarna 455 Rancher?

To adjust the bar oiler on your Husqvarna 455 Rancher, follow these steps:

1. Turn off the chainsaw and allow it to cool down.
2. Remove the bar cover.
3. Locate the bar oiler adjustment screw.
4. Turn the screw clockwise to increase the oil flow or counterclockwise to decrease the oil flow.
5. Reinstall the bar cover.

How much oil does the bar oiler on my Husqvarna 455 Rancher use?

The bar oiler on your Husqvarna 455 Rancher uses approximately 1 ounce of oil per hour.

What happens if the bar oiler on my Husqvarna 455 Rancher is not working?

If the bar oiler on your Husqvarna 455 Rancher is not working, it can cause the chain to overheat and wear out prematurely. It can also damage the bar and sprocket.

How can I prevent the bar oiler on my Husqvarna 455 Rancher from clogging?

To prevent the bar oiler on your Husqvarna 455 Rancher from clogging, follow these tips:

Use high-quality bar oil.
Clean the bar oiler regularly.
Avoid operating the chainsaw in dusty or dirty conditions.
Store the chainsaw in a clean, dry place.

Next Post You May Like: Husqvarna Chainsaw 455 Rancher Chain Oiler Not Working