John Deere Chainsaw Bar Oiler Not Working

As a chainsaw owner, there’s nothing more frustrating than having your bar oiler stop working. Not only does it make it difficult to keep your chain sharp and running smoothly, but it can also be dangerous. A dull chain is more likely to kickback, which can cause serious injury.

If your John Deere chainsaw bar oiler isn’t working, don’t panic. There are a few simple troubleshooting steps you can take to diagnose and resolve the problem. In this guide, I’ll walk you through the process, so you can get your chainsaw back up and running in no time.

Most Common Reasons Of John Deere Chainsaw Bar Oiler Not Working

Most Common Reasons Of John Deere Chainsaw Bar Oiler Not Working

1. Insufficient Oil Level

The most common reason for a John Deere chainsaw bar oiler not working is insufficient oil level. To check the oil level, remove the oil cap and look inside the oil reservoir. The oil level should be between the full and add marks. If the oil level is low, add oil to the reservoir until it reaches the full mark.

2. Clogged Oil Filter

Another common reason for a John Deere chainsaw bar oiler not working is a clogged oil filter. To check the oil filter, remove it from the chainsaw and inspect it for debris. If the filter is clogged, replace it with a new one.

3. Faulty Oil Pump

If the oil level is correct and the oil filter is not clogged, the problem may be a faulty oil pump. To test the oil pump, start the chainsaw and listen for the oil pump to operate. If you do not hear the oil pump running, the pump may be faulty and will need to be replaced.

4. Plugged Oil Hose

A plugged oil hose can also prevent the oil from reaching the bar and chain. To check the oil hose, remove it from the chainsaw and inspect it for debris. If the hose is plugged, clear the debris and reinstall the hose.

5. Misaligned Oiler Tube

The oiler tube on a John Deere chainsaw can become misaligned, which can prevent the oil from reaching the bar and chain. To check the oiler tube, remove the bar and chain from the chainsaw. Inspect the oiler tube for any damage or misalignment. If the oiler tube is damaged or misaligned, it will need to be replaced.

How to Troubleshoot: John Deere Chainsaw Bar Oiler Not Working

Symptoms of a Chainsaw Bar Oiler Not Working

There are a few signs that your John Deere chainsaw bar oiler may not be working properly. These include:

The chain is not being lubricated properly, which can lead to excessive wear and tear on the chain and bar.
The bar oil reservoir is empty or nearly empty.
The oiler is not pumping oil to the bar.
The oiler is leaking oil.

Troubleshooting a Chainsaw Bar Oiler

If you suspect that your John Deere chainsaw bar oiler is not working properly, you can troubleshoot the problem by following these steps:

1. Check the oil level. The first thing you should do is check the oil level in the reservoir. If the reservoir is empty or nearly empty, you will need to refill it with the correct type of oil.
2. Check the oiler pump. The oiler pump is responsible for pumping oil to the bar. To check the oiler pump, start the chainsaw and listen for a whining sound. If you do not hear a whining sound, the oiler pump may be defective.
3. Check the oiler hose. The oiler hose is responsible for transporting oil from the reservoir to the bar. To check the oiler hose, look for leaks. If you see any leaks, the oiler hose may be damaged and will need to be replaced.
4. Check the oiler orifice. The oiler orifice is a small hole in the bar that allows oil to be sprayed onto the chain. To check the oiler orifice, remove the bar from the chainsaw and look for any obstructions. If you see any obstructions, you will need to clean the oiler orifice.

How to Fix a Chainsaw Bar Oiler

If you have determined that your John Deere chainsaw bar oiler is not working properly, you can fix the problem by following these steps:

1. Refill the oil reservoir. If the oil level is low, refill the reservoir with the correct type of oil.
2. Replace the oiler pump. If the oiler pump is defective, you will need to replace it with a new one.
3. Replace the oiler hose. If the oiler hose is damaged, you will need to replace it with a new one.
4. Clean the oiler orifice. If the oiler orifice is obstructed, you will need to clean it with a small brush.

Preventing Chainsaw Bar Oiler Problems

You can help prevent problems with your John Deere chainsaw bar oiler by following these tips:

Keep the oil level in the reservoir full.
Use the correct type of oil.
Inspect the oiler pump, hose, and orifice regularly for leaks or damage.
Clean the oiler orifice regularly.

By following these tips, you can help keep your John Deere chainsaw bar oiler working properly and extend its lifespan.

FAQs: John Deere Chainsaw Bar Oiler Not Working

Why is my John Deere chainsaw bar oiler not working?

There are a few possible reasons why your John Deere chainsaw bar oiler may not be working. Here are some of the most common causes:

The oiler is not getting enough oil. Make sure that the oil level in the oil reservoir is full. If the oil level is low, add more oil to the reservoir.
The oiler is clogged. The oiler may be clogged with sawdust or other debris. To clean the oiler, remove the oiler cover and clean the inside of the oiler with a small brush.
The oiler is not pumping oil. The oiler may not be pumping oil if the oil pump is damaged. If the oil pump is damaged, it will need to be replaced.
The oiler hose is kinked or damaged. The oiler hose may be kinked or damaged, preventing oil from flowing to the bar. If the oiler hose is kinked or damaged, it will need to be replaced.

How do I fix my John Deere chainsaw bar oiler?

To fix your John Deere chainsaw bar oiler, you will need to identify the cause of the problem and then take the appropriate steps to fix it. Here are the steps to take to fix a John Deere chainsaw bar oiler:

1. Check the oil level. Make sure that the oil level in the oil reservoir is full. If the oil level is low, add more oil to the reservoir.
2. Clean the oiler. Remove the oiler cover and clean the inside of the oiler with a small brush.
3. Check the oil pump. If the oil pump is damaged, it will need to be replaced.
4. Check the oiler hose. If the oiler hose is kinked or damaged, it will need to be replaced.

What is the difference between a manual and an automatic chainsaw bar oiler?

A manual chainsaw bar oiler requires the operator to manually pump the oiler to deliver oil to the bar. An automatic chainsaw bar oiler automatically delivers oil to the bar as the chainsaw is operated.

Manual chainsaw bar oilers are less expensive than automatic chainsaw bar oilers. However, manual chainsaw bar oilers can be more difficult to use and can result in less consistent oil delivery.

Automatic chainsaw bar oilers are more expensive than manual chainsaw bar oilers. However, automatic chainsaw bar oilers are easier to use and can result in more consistent oil delivery.

How often should I oil the bar on my John Deere chainsaw?

You should oil the bar on your John Deere chainsaw every time you use it. You should also oil the bar if the bar becomes dry or if the bar starts to smoke.

To oil the bar, remove the oiler cover and pour a small amount of oil onto the bar. Then, turn on the chainsaw and let the oil run down the bar.

What happens if I don’t oil the bar on my John Deere chainsaw?

If you don’t oil the bar on your John Deere chainsaw, the bar can become dry and hot. This can damage the bar and can also cause the bar to smoke.

It is important to oil the bar on your John Deere chainsaw to prevent damage to the bar and to ensure that the chainsaw operates properly.

Next Post You May Like: Jonsered Chainsaw Oiler Not Working