Poulan Chainsaw Bar Oiler Not Working
As a chainsaw repair professional, I have seen firsthand the frustration and inconvenience that can be caused by a . A malfunctioning bar oiler can quickly lead to a dull chain, which can be dangerous and inefficient. It can also damage the chainsaw itself. By quickly diagnosing and resolving the problem, you can restore functionality to your tool and avoid these potential hazards.
In this guide, I will walk you through the steps of troubleshooting a Poulan chainsaw bar oiler that is not working. I will cover common causes of the problem, as well as the steps you can take to fix it. By following these steps, you can get your chainsaw back up and running in no time.
Most Common Reasons Of Poulan Chainsaw Bar Oiler Not Working
Most Common Reasons Of Poulan Chainsaw Bar Oiler Not Working
1. Insufficient Oil
The most common reason for a Poulan chainsaw bar oiler not working is insufficient oil. This can be caused by a number of factors, including:
Low oil level: The oil level in the chainsaw’s reservoir should be between the full and add marks. If the oil level is low, add more oil to the reservoir.
Clogged oil filter: The oil filter can become clogged with sawdust and other debris, preventing oil from reaching the bar and chain. To clean the oil filter, remove it from the chainsaw and rinse it with warm, soapy water.
Blocked oil line: The oil line can become blocked with sawdust and other debris, preventing oil from reaching the bar and chain. To clear the oil line, remove the bar and chain from the chainsaw and use a small wire brush to clean the oil line.
2. Faulty Oiler Pump
The oiler pump is responsible for pumping oil from the reservoir to the bar and chain. If the oiler pump is faulty, it will not be able to pump oil to the bar and chain, causing the bar oiler to not work.
To check if the oiler pump is faulty, remove the bar and chain from the chainsaw and turn the engine on. If the oiler pump is working properly, you should see oil flowing from the oiler hole in the bar. If you do not see oil flowing from the oiler hole, the oiler pump is faulty and will need to be replaced.
3. Blocked Oiler Hole
The oiler hole is located in the bar and is responsible for allowing oil to flow from the oiler pump to the bar and chain. If the oiler hole is blocked, oil will not be able to flow to the bar and chain, causing the bar oiler to not work.
To check if the oiler hole is blocked, remove the bar and chain from the chainsaw. Use a small wire brush to clean the oiler hole. If the oiler hole is still blocked, you may need to replace the bar.
4. Incorrect Oil Viscosity
The oil viscosity is the thickness of the oil. The correct oil viscosity for your chainsaw is listed in the owner’s manual. If you use oil that is too thin, it will not be able to lubricate the bar and chain properly. If you use oil that is too thick, it will not be able to flow through the oiler pump and oiler hole properly.
To check if the oil viscosity is correct, refer to the owner’s manual for your chainsaw. If you are not sure what oil viscosity to use, consult with a qualified chainsaw technician.
How to Troubleshoot: Poulan Chainsaw Bar Oiler Not Working
Symptoms of a Poulan Chainsaw Bar Oiler Not Working
There are a few telltale signs that your Poulan chainsaw bar oiler is not working properly. These include:
The bar oil reservoir is empty or low.
The bar oil is not flowing to the bar and chain.
The bar and chain are becoming hot and smoking.
The chain is skipping or binding.
Troubleshooting a Poulan Chainsaw Bar Oiler
If you are experiencing any of the symptoms listed above, it is important to troubleshoot the problem and fix it as soon as possible. Here are a few steps to help you troubleshoot your Poulan chainsaw bar oiler:
1. Check the oil level. The first step is to check the oil level in the reservoir. If the reservoir is empty or low, fill it up with fresh bar oil.
2. Check the oil flow. Next, you need to check the oil flow to the bar and chain. To do this, start the chainsaw and let it run for a few minutes. Then, look at the bar oil hole and see if oil is flowing out. If no oil is flowing, there is a problem with the oiler.
3. Inspect the oiler. If no oil is flowing from the bar oil hole, you need to inspect the oiler. Look for any damage or blockages. If you find any damage, you will need to replace the oiler.
4. Clean the bar and chain. If the oiler is working properly but the bar and chain are still becoming hot and smoking, you need to clean them. To do this, use a soft cloth to wipe off any dirt or debris.
5. Adjust the bar oiler. If the bar and chain are skipping or binding, you may need to adjust the bar oiler. To do this, turn the oiler adjustment screw clockwise to increase the oil flow or counterclockwise to decrease the oil flow.
Preventing Poulan Chainsaw Bar Oiler Problems
The best way to prevent Poulan chainsaw bar oiler problems is to keep your chainsaw clean and well-maintained. Here are a few tips to help you prevent problems:
Check the oil level regularly. Make sure to check the oil level in the reservoir regularly and add oil as needed.
Clean the bar and chain regularly. Wipe off any dirt or debris from the bar and chain after each use.
Adjust the bar oiler as needed. Adjust the bar oiler to ensure that the proper amount of oil is flowing to the bar and chain.
By following these tips, you can help prevent Poulan chainsaw bar oiler problems and keep your chainsaw running smoothly.
FAQs: Poulan Chainsaw Bar Oiler Not Working
Why is my Poulan chainsaw bar oiler not working?
There are a few possible reasons why your Poulan chainsaw bar oiler might not be working. Here are some of the most common causes:
The oiler is clogged. The oiler can become clogged with sawdust or other debris, which can prevent the oil from reaching the bar and chain. To clean the oiler, remove the cover and use a small brush to clean out any debris.
The oiler is not getting enough oil. The oiler needs to be filled with the correct type and amount of oil. If the oiler is not getting enough oil, the bar and chain will not be properly lubricated and may overheat.
The oiler is not working properly. The oiler may be defective and need to be replaced. If you suspect that the oiler is defective, take your chainsaw to a qualified service center for diagnosis and repair.
How do I fix a Poulan chainsaw bar oiler that is not working?
To fix a Poulan chainsaw bar oiler that is not working, you will need to identify the cause of the problem and take the appropriate steps to fix it. Here are some steps to help you troubleshoot the problem:
1. Check the oil level. Make sure that the oiler is filled with the correct type and amount of oil.
2. Clean the oiler. Remove the cover and use a small brush to clean out any debris.
3. Check the oiler hose. Make sure that the oiler hose is not kinked or damaged.
4. Check the oiler pump. Make sure that the oiler pump is working properly.
5. Replace the oiler. If the oiler is defective, you will need to replace it.
What is the difference between a Poulan chainsaw bar oiler and a chain oiler?
A Poulan chainsaw bar oiler is a device that lubricates the bar and chain of a chainsaw. A chain oiler is a device that lubricates the chain of a chainsaw. The main difference between the two is that a bar oiler lubricates the bar as well as the chain, while a chain oiler only lubricates the chain.
How often should I oil the bar and chain on my Poulan chainsaw?
You should oil the bar and chain on your Poulan chainsaw every time you use it. This will help to prevent the bar and chain from overheating and wearing out prematurely.
What type of oil should I use for my Poulan chainsaw?
You should use a high-quality bar and chain oil for your Poulan chainsaw. Bar and chain oil is designed to provide lubrication and cooling for the bar and chain, and it will help to extend the life of your chainsaw.
Next Post You May Like: Poulan Chainsaw Brake Not Working
