Have you ever been using your Poulan 14-inch electric chainsaw and had the chain come loose It’s a frustrating experience, but it’s one that’s easy to fix. In this blog post, I’ll show you how to tighten the chain on your Poulan 14-inch electric chainsaw in just a few simple steps. So if you’re ready to get back to cutting wood, keep reading!
So Poullan 14 Electric Chain Saw Chain Keeps Coming Loose
To keep the chain from coming loose on a Poulan 14 electric chainsaw, tighten the chain by turning the adjusting screw clockwise until the chain is snug against the bar. Be sure not to overtighten the chain, as this can damage the saw.
Poulan 14 Electric Chain Saw Chain Keeps Coming Loose
Problem
If the chain on your Poulan 14 electric chain saw keeps coming loose, there are a few possible causes.
The chain is too loose:
The chain should be snug against the bar, but not so tight that it is difficult to turn the saw. If the chain is too loose, it will come loose more easily.
The chain is worn out:
A worn-out chain will stretch and become loose. It is important to replace the chain regularly, as per the manufacturer’s recommendations.
The bar is bent:
A bent bar can cause the chain to come loose. If the bar is bent, it should be straightened or replaced.
The chain tensioner is not adjusted correctly:
The chain tensioner is responsible for keeping the chain tight against the bar. If the tensioner is not adjusted correctly, the chain will come loose.
Solution
To fix the problem of a loose chain on your Poulan 14 electric chain saw, you will need to identify the cause of the problem and then take the appropriate steps to fix it.
If the chain is too loose, tighten it by turning the tensioner knob clockwise:
Be careful not to overtighten the chain, as this can damage the saw.
If the chain is worn out, replace it with a new one:
When replacing the chain, be sure to use the correct size and type of chain for your saw.
If the bar is bent, straighten it or replace it:
If you are unable to straighten the bar, you will need to replace it.
If the chain tensioner is not adjusted correctly, adjust it by turning the tensioner knob clockwise or counterclockwise:
Be sure to adjust the tensioner so that the chain is snug against the bar, but not so tight that it is difficult to turn the saw.
Prevention
To prevent the chain on your Poulan 14 electric chain saw from coming loose, you can take the following steps:
Tighten the chain regularly:
Check the chain tension every time you use the saw and tighten it as needed.
Replace the chain regularly:
Replace the chain according to the manufacturer’s recommendations.
Inspect the bar for damage:
Inspect the bar for bends or other damage and replace it if necessary.
Adjust the chain tensioner correctly:
Make sure that the chain tensioner is adjusted correctly so that the chain is snug against the bar, but not so tight that it is difficult to turn the saw.
By following these tips, you can help to prevent the chain on your Poulan 14 electric chain saw from coming loose.
Also Read THis: Ridgid Miter Saw Electric Brake Not Working
FAQs: Poulan 14 Electric Chain Saw Chain Keeps Coming Loose
Why is the chain on my Poulan 14 electric chain saw coming loose?
There are a few possible reasons why the chain on your Poulan 14 electric chain saw is coming loose.
The chain is not properly tensioned: The chain should be tight enough to stay on the bar, but not so tight that it is difficult to move. To check the tension, hold the saw with the chain off the ground and pull on the chain with your hand. The chain should move about 1/8 inch up and down. If it moves more than that, you need to tighten the chain.
The chain is worn out: Chains wear out over time, and as they do, they become looser. If the chain is worn out, you will need to replace it.
The bar is bent: If the bar is bent, it can cause the chain to come loose. If the bar is bent, you will need to have it straightened or replaced.
The sprocket is worn out: The sprocket is the part of the saw that drives the chain. If the sprocket is worn out, it can cause the chain to come loose. If the sprocket is worn out, you will need to replace it.
How do I tighten the chain on my Poulan 14 electric chain saw?
To tighten the chain on your Poulan 14 electric chain saw, follow these steps:
1. Turn off the saw and disconnect the spark plug wire.
2. Use the chain tensioner to loosen the chain.
3. Move the chain up so that it is tight against the bar.
4. Tighten the chain tensioner until the chain is snug.
5. Reattach the spark plug wire.
How do I know if the chain on my Poulan 14 electric chain saw is worn out?
There are a few ways to tell if the chain on your Poulan 14 electric chain saw is worn out.
The chain is dull: A dull chain will not cut through wood as easily as a sharp chain. You can check the sharpness of the chain by running your finger along the teeth. If the teeth are smooth, the chain is dull.
The chain is stretched: A stretched chain will be loose on the bar. You can check the tension of the chain by holding the saw with the chain off the ground and pulling on the chain with your hand. The chain should move about 1/8 inch up and down. If it moves more than that, the chain is stretched.
The chain has broken links: A chain with broken links will not work properly. You will need to replace the chain if it has any broken links.
How do I fix a bent bar on my Poulan 14 electric chain saw?
To fix a bent bar on your Poulan 14 electric chain saw, follow these steps:
1. Remove the chain from the bar.
2. Use a vice to hold the bar in place.
3. Use a hammer to straighten the bar.
4. Reattach the chain to the bar.
How do I replace the sprocket on my Poulan 14 electric chain saw?
To replace the sprocket on your Poulan 14 electric chain saw, follow these steps:
1. Turn off the saw and disconnect the spark plug wire.
2. Remove the chain from the bar.
3. Remove the sprocket cover.
4. Remove the old sprocket.
5. Install the new sprocket.
6. Reattach the sprocket cover.
7. Reattach the chain to the bar.
