If your Simpson pressure washer siphon isn’t working, you’re not alone. This is a common problem that can be frustrating and inconvenient. But don’t worry, it’s usually an easy fix.
In this guide, I’ll walk you through the steps to troubleshoot and fix a Simpson pressure washer siphon that isn’t working. I’ll also provide some tips on how to prevent this problem from happening in the future.
So if your Simpson pressure washer siphon isn’t working, read on for help!
Reasons Why Simpson Pressure Washer Siphon Not Working
Dirty Filter
The most common reason for a Simpson pressure washer siphon not working is a dirty filter. The filter prevents dirt and debris from entering the pump, and if it becomes clogged, it can restrict the flow of water and prevent the siphon from working properly. To clean the filter, remove it from the pump and rinse it under warm water. If the filter is badly clogged, you may need to replace it.
Low Water Pressure
Another common cause of a Simpson pressure washer siphon not working is low water pressure. This can be caused by a number of factors, including a faulty water supply line, a clogged nozzle, or a problem with the pump. To check the water pressure, turn on the pressure washer and attach a pressure gauge to the outlet. If the pressure is below 200 psi, there is a problem with the water supply.
Clogged Nozzle
A clogged nozzle can also prevent the Simpson pressure washer siphon from working properly. The nozzle is located at the end of the wand, and it directs the water stream. If the nozzle becomes clogged with dirt or debris, it can restrict the flow of water and prevent the siphon from working. To clean the nozzle, remove it from the wand and soak it in a solution of warm water and dish soap. If the nozzle is badly clogged, you may need to use a needle to clear the obstruction.
Faulty Pump
If the Simpson pressure washer siphon is not working, it is possible that the pump is faulty. The pump is responsible for generating the pressure that powers the pressure washer, and if it is not working properly, it can prevent the siphon from working. To check the pump, turn on the pressure washer and listen for any unusual noises. If you hear a whining or grinding noise, the pump may be faulty. You can also check the pump for leaks. If you see any leaks, the pump will need to be repaired or replaced.
How to Troubleshoot and Fix: Simpson Pressure Washer Siphon Not Working
Symptoms of a Simpson Pressure Washer Siphon Not Working
There are a few telltale signs that your Simpson pressure washer siphon is not working properly. These include:
The pressure washer is not producing any pressure.
The pressure washer is producing very low pressure.
The pressure washer is making a gurgling or bubbling sound.
The pressure washer is leaking water from the bottom.
Causes of a Simpson Pressure Washer Siphon Not Working
There are a number of things that can cause a Simpson pressure washer siphon to stop working. These include:
A clogged or kinked siphon hose.
A dirty or damaged siphon jet.
A faulty pressure washer pump.
A problem with the water supply.
How to Troubleshoot a Simpson Pressure Washer Siphon
To troubleshoot a Simpson pressure washer siphon, you will need to:
1. Inspect the siphon hose for any clogs or kinks. If you find a clog, you can try to clear it by using a wire hanger. If the hose is kinked, you will need to replace it.
2. Clean the siphon jet. To do this, remove the jet from the pressure washer and soak it in a cleaning solution. You can also use a wire brush to clean the jet.
3. Check the pressure washer pump for any damage. If the pump is damaged, you will need to replace it.
4. Check the water supply. Make sure that the water supply is turned on and that the pressure is sufficient.
How to Fix a Simpson Pressure Washer Siphon
Once you have identified the cause of the problem, you can fix the Simpson pressure washer siphon. Here are the steps to follow:
1. To fix a clogged or kinked siphon hose, you will need to replace the hose. To do this, disconnect the hose from the pressure washer and the water source. Then, attach the new hose to the pressure washer and the water source.
2. To clean the siphon jet, you will need to remove the jet from the pressure washer and soak it in a cleaning solution. You can also use a wire brush to clean the jet.
3. To replace the pressure washer pump, you will need to disconnect the pump from the pressure washer. Then, remove the old pump and install the new pump.
4. To fix a problem with the water supply, you will need to check the water supply valve and make sure that it is turned on. You will also need to check the water pressure and make sure that it is sufficient.
Preventing Simpson Pressure Washer Siphon Problems
You can prevent Simpson pressure washer siphon problems by following these tips:
Keep the siphon hose free of clogs and kinks.
Clean the siphon jet regularly.
Inspect the pressure washer pump regularly for damage.
Check the water supply valve and water pressure regularly.
By following these tips, you can help to keep your Simpson pressure washer siphon working properly.
Also Read THis: Simpson Pressure Washer Soap Not Working
FAQs about Simpson Pressure Washer Siphon Not Working
Why is my Simpson pressure washer siphon not working?
There are a few possible reasons why your Simpson pressure washer siphon might not be working. Here are some of the most common causes:
The siphon hose is kinked or blocked: Make sure that the hose is clear and free of kinks. If it is kinked, you can try straightening it out or replacing it.
The siphon tube is clogged: The siphon tube is a small tube that connects the water inlet to the pump. If it is clogged, it will prevent water from flowing into the pump. You can try cleaning the tube with a small brush or replacing it if it is damaged.
The pump is not primed: The pump needs to be primed before it can start siphoning water. To prime the pump, turn on the water supply and hold the trigger on the gun until water starts to flow out.
The pressure switch is not working properly: The pressure switch is a valve that controls the flow of water to the pump. If it is not working properly, it can prevent the pump from starting. You can try replacing the pressure switch if it is faulty.
How do I fix my Simpson pressure washer siphon?
To fix your Simpson pressure washer siphon, you will need to identify the cause of the problem and then take steps to fix it. Here are some steps you can take to troubleshoot the problem:
1. Check the siphon hose for kinks or blockages. If the hose is kinked, you can try straightening it out or replacing it.
2. Check the siphon tube for clogs. If the tube is clogged, you can try cleaning it with a small brush or replacing it.
3. Prime the pump. To prime the pump, turn on the water supply and hold the trigger on the gun until water starts to flow out.
4. Check the pressure switch. If the pressure switch is not working properly, you can try replacing it.
What are the symptoms of a Simpson pressure washer siphon not working?
There are a few symptoms that you might notice if your Simpson pressure washer siphon is not working properly. These include:
The pressure washer is not producing any water or is producing very little water.
The pressure washer is making a loud whining or buzzing noise.
The pressure washer is overheating.
The pressure washer is leaking water.
What are the dangers of a Simpson pressure washer siphon not working?
There are a few dangers associated with a Simpson pressure washer siphon not working properly. These include:
The pressure washer could overheat and cause a fire.
The pressure washer could leak water and cause damage to your property.
The pressure washer could not produce enough water to clean your surfaces effectively.
How can I prevent my Simpson pressure washer siphon from not working?
There are a few things you can do to prevent your Simpson pressure washer siphon from not working. These include:
Keep the siphon hose and tube free of kinks and blockages.
Prime the pump before you use it.
Check the pressure switch regularly and replace it if it is faulty.
Clean the pressure washer regularly to prevent it from overheating.
