Your Troy-Bilt pressure washer is one of the most valuable tools in your home improvement arsenal. But when the siphon isn’t working, it can be a major pain. Not only is it frustrating to deal with, but it can also be dangerous. If the siphon isn’t working properly, you could end up with hot water spraying all over you.
In this guide, I’ll show you how to troubleshoot a Troy-Bilt pressure washer that’s not siphoning. I’ll cover the most common causes of this problem and give you step-by-step instructions on how to fix them. By the end of this guide, you’ll be able to get your pressure washer back up and running in no time.
Why Troy Bilt Pressure Washer Siphon Not Working
Dirty Water Filter
The water filter on a pressure washer is responsible for removing dirt and debris from the water before it is used to power the pump. If the filter becomes clogged with dirt and debris, it can restrict the flow of water to the pump, causing the siphon to stop working.
Low Water Pressure
If the water pressure is too low, it can cause the siphon to stop working. This can be caused by a number of factors, including:
A kinked or damaged hose
A clogged nozzle
A faulty pump
Air in the System
If there is air in the system, it can prevent the siphon from working properly. This can be caused by:
A loose or damaged hose connection
A faulty pump
A leak in the system
Faulty Siphon Valve
The siphon valve is a small valve that allows water to flow from the tank to the pump. If the valve is faulty, it can prevent the siphon from working properly.
Other Causes
There are a number of other potential causes of a pressure washer siphon not working, including:
A faulty pressure switch
A faulty pressure regulator
A faulty water pump
How to Troubleshoot And Fix: Troy Bilt Pressure Washer Siphon Not Working
Symptoms of a Troy Bilt Pressure Washer Siphon Not Working
There are a few different symptoms that can indicate that the siphon on your Troy Bilt pressure washer is not working properly. These include:
The pressure washer is not producing any or very little pressure.
The pressure washer is making a gurgling or bubbling noise.
The pressure washer is leaking water from the bottom.
The pressure washer is not starting or running properly.
Troubleshooting a Troy Bilt Pressure Washer Siphon
If you are experiencing any of the symptoms listed above, it is likely that the siphon on your pressure washer is not working properly. To troubleshoot the problem, follow these steps:
1. Check the hose connections:
Make sure that the hoses connecting the pressure washer to the water source and the spray gun are properly connected. If the hoses are not connected properly, water will not be able to flow through the siphon and the pressure washer will not produce any pressure.
2. Check the siphon tube:
The siphon tube is a small tube that connects the water inlet on the pressure washer to the pump. If the siphon tube is clogged, water will not be able to flow through the siphon and the pressure washer will not produce any pressure. To check the siphon tube, remove it from the pressure washer and inspect it for any obstructions. If you find any obstructions, remove them and then reattach the siphon tube.3. Check the check valve:
The check valve is a small valve that prevents water from flowing back into the water source when the pressure washer is turned off. If the check valve is not working properly, water will be able to flow back into the water source and the pressure washer will not produce any pressure. To check the check valve, remove it from the pressure washer and inspect it for any damage. If you find any damage, replace the check valve.
4. Clean the pump:
The pump is the heart of the pressure washer and if it is dirty, it will not be able to produce any pressure. To clean the pump, remove it from the pressure washer and disassemble it. Then, use a brush and some warm, soapy water to clean all of the parts. Be sure to rinse the pump thoroughly after cleaning it.
Fixing a Troy Bilt Pressure Washer Siphon
Once you have identified the problem with the siphon on your Troy Bilt pressure washer, you can fix it by following these steps:
1. Replace the hoses:
If the hoses are clogged or damaged, replace them with new ones.
2. Replace the siphon tube:
If the siphon tube is clogged, replace it with a new one.3. Replace the check valve:
If the check valve is damaged, replace it with a new one.
4. Clean the pump:
If the pump is dirty, clean it according to the instructions in the owner’s manual.
Preventing Problems with Your Troy Bilt Pressure Washer Siphon
You can prevent problems with your Troy Bilt pressure washer siphon by following these tips:
Keep the hoses connected properly:
Make sure that the hoses connecting the pressure washer to the water source and the spray gun are properly connected.
Clean the siphon tube regularly:
The siphon tube is a small tube that can easily become clogged. To prevent this, clean the siphon tube regularly with a brush and some warm, soapy water.
Inspect the check valve regularly:
The check valve is a small valve that can easily become damaged. To prevent this, inspect the check valve regularly for any damage.
Clean the pump regularly:
The pump is the heart of the pressure washer and if it is dirty, it will not be able to produce any pressure. To prevent this, clean the pump regularly according to the instructions in the owner’s manual.
FAQs: Troy Bilt Pressure Washer Siphon Not Working
Why is my Troy Bilt pressure washer siphon not working?
There are a few possible reasons why your Troy Bilt pressure washer siphon may not be working.
The siphon hose is kinked or clogged: Make sure that the hose is not kinked or clogged. If it is, straighten it out or clear the clog.
The siphon tube is not properly inserted into the water inlet: Make sure that the siphon tube is properly inserted into the water inlet.
The water inlet valve is not open: Make sure that the water inlet valve is open.
The pressure washer pump is not working properly: If the pressure washer pump is not working properly, it will not be able to create enough suction to draw water up the siphon hose.
The pressure washer tank is empty: If the pressure washer tank is empty, the siphon will not be able to draw water up the hose.
How do I fix my Troy Bilt pressure washer siphon?
To fix your Troy Bilt pressure washer siphon, you will need to identify the problem and then take the appropriate steps to fix it.
If the siphon hose is kinked or clogged, straighten it out or clear the clog.
If the siphon tube is not properly inserted into the water inlet, make sure that it is properly inserted.
If the water inlet valve is not open, open it.
If the pressure washer pump is not working properly, have it serviced or replaced.
If the pressure washer tank is empty, fill it up.
What are the symptoms of a Troy Bilt pressure washer siphon not working?
There are a few symptoms that may indicate that your Troy Bilt pressure washer siphon is not working properly.
The pressure washer is not producing any pressure:
The pressure washer is making a gurgling or sucking sound:
The pressure washer is leaking water from the siphon hose:
The pressure washer is not able to draw water up the siphon hose:
How can I prevent my Troy Bilt pressure washer siphon from not working?
There are a few things you can do to prevent your Troy Bilt pressure washer siphon from not working.
Make sure that the siphon hose is not kinked or clogged:
Make sure that the siphon tube is properly inserted into the water inlet:
Make sure that the water inlet valve is open:
Keep the pressure washer tank full:
Have the pressure washer pump serviced regularly:
What should I do if my Troy Bilt pressure washer siphon is still not working after I have tried to fix it?
If your Troy Bilt pressure washer siphon is still not working after you have tried to fix it, you should contact a qualified technician for assistance.
Also Read: Troy Bilt Pressure Washer Soap Dispenser Not Working
